720738
9
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
(Original instructions) ENGLISH
9
Setting the angle (Fig. J)
Set the required bevel angle from 0 to 45 degree
Before cutting, ensure the saw blade (4) and mitre
gauge (6) no collision
- Loose the Bevel adjustment locking knob (10).
- Set up the desired angle then lock the knob again
Working with the rip fence
Setting the fence height (Fig. K)
- The fence rail (i) of the rip fence (5) has two guiding
surface with different heights.
- Depending on the thickness of the material to be cut, the
higher side of the fence rail (i) has to be used for thick
material (work piece thickness above 25mm) and the
lower side of the fence rail for thin material (work piece
thickness below 25mm).
- For the adjustment, loosen the bolts on the side of the rip
fence (5) and push the fence rail (i) on he guide,
depending on the required position.
- Tighten the bolts again.
Rip fence assembly (Fig. L)
- Fix the rip fence (5) at the back side and press the locking
handle (15) downwards.
- When disassembly, pull the locking handle up and remove
the rip fence (5).
- The rip fence could be locked setting with the rear knurled
nut.
5. Warning! Turn the nut in the rotational direction of the saw
blade.
6. Remove the outer flange and take out the saw blade from
the inner flange, with diagonally downwards movement.
7. Carefully clean the flange with a before fixing the new saw
blade.
8. Insert the new saw blade and fasten the outer flange. The
outer flange has a Φ30mm raised boss which fits in side
the blade bore.
Warning! The teeth of a new blade are very sharp and can be
dangerous. Make sure the teeth point down at the front of the
table, aligned with the arrow marked on the saw blade guard
(2).
9. Attach the table insert (20) and the saw blade guard (2)
again and set them.
10. Before working, check the functionality of the guards.
On/Off switch (Fig. J)
- To switch the machine on, press the green start “I” button.
- To switch the machine off, press the red stop “O” button.
Cutting depth (Fig. J)
Turn the blade elevation handle (11) to set the blade to the
required cutting depth.
- Turn anti-clockwise; to increase the cutting depth
- Turn Clockwise; to reduce the cutting depth
After each new adjustment it is advisable to carry out a trial
cut in order to check the set dimensions.
I
17 17
J
8
11
10
K
i5
L
515
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stanley SST1800 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info