Bedienungsanleitung Stanley ST-033-240-E (Seite 128 von 141) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

720245

128

Zoom out

Zoom in

Vorherige Seite

1/141

Nächste Seite

NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE

Assembly (See Page 6)

1. ASSEMBLE TOP HANDLE BRACKET (Fig. 1)

i. Slide upper handle brackets onto front handle

and align holes.

ii. Slide rear handle into upper handle brackets

and align holes.

2. INSTALL HEATER LEG FRAME (Fig. 2)

i. Align lower inner bracket with holes in heater.

ii. Attach aligned holes in Heater leg frame with

lower inner bracket.

iii. Align lower outer bracket holes with lower inner

bracket, and attach using 2 bottom screws.

3. INSTALL SIDE SUPPORTS (Fig. 3)

i. Slide side support into lower bracket and align

holes.

ii. Attach using top remaining screw.

4. INSTALL TOP HANDLE BRACKET (Fig. 4)

i. Slide side support into upper bracket and align

holes.

ii. Attach upper brackets to heater using 3 screws

per side.

Operation

1. Position the fan heater so that it stands upright

on a firm, level surface and at a safe distance

from wet environments and flammable objects.

2. Connect the fan heater to the proper electrical

power.

3. Set the thermostat dial to the maximum

temperature.

4. The fan heater will switch on when the function

selector dial is set to one of the power settings.

5. Once the room reaches the desired

temperature, turn the thermostat dial back

until heating element turns off.

Automatic Overheat Safety Control

– This heater is equipped with safety internal

heat limiting thermostat and overheat

protection circuit. When a potential overheat

temperature is reached, the system will

automatically shut the heater off

Thermostat Instructions

– At first, set the thermostat to “+” and let the

heater operate with full power input. When

the room temperature reaches the required

value, turn the thermostat to the left until it

switches off.

– The thermostat will then switch on and off

automatically to control the room temperature

according to the preset value and keep the

room temperature constant.

– When using the heater for the first time, you

may notice a slight emission of smoke. This

is quite normal and it stops after a short

time. The heating element is made of steel

and was coated with a layer of protective oil

during production. The smoke is caused by

the leftover oil as it is heated.

Cleaning and Maintenance

– Before cleaning the appliance, disconnect it

from the outlet and let it cool down.

– The enclosure is easy to get dirty. Wipe it

often with a soft sponge. For very dirty parts,

wipe with a sponge dipped in < 50°C water

and mild detergent, then dry the heater

enclosure with a clean cloth. Be careful not to

let the water enter the inside of the appliance

– In order to protect the enclosure, don’t

splash water onto the heater, and never

use a solvent like gasoline, isoamyl acetate,

toluene, etc. to clean the heater.

– When you store the heater, let it cool down

first and, keep it dry. Then cover it with a

plastic bag, put it in the packing box and

store it in a dry, ventilated place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley ST-033-240-E Seite 128

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info