Bedienungsanleitung Stanley ST-125T-KFA-E (Seite 80 von 85) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

720272

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

1030 Brussels, Belgium

NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE

TROUBLESHOOTING GUIDE

Problem

Possible Cause Solution

Heater fires, but Main PCB shuts

heater off after a short period of time.

Lamp is flickering, and LED display

shows “E1”

1. Incorrect pump pressure

2. Dirty Input, Output or Lint Filter

3. Dirty Fuel Filter

4. Nozzle is Dirty

5. Photocell lens is Dirty

6. Photocell not installed properly

7. Photocell Defective

8. Improper electrical connection

between Main PCB and Photocell

1. Adjust Pump Pressure

2. Clean/replace Air Filter

3. Clean/replace Fuel Filter

4. Clean/replace Nozzle

5. Clean/replace Photocell

6. Adjust Photocell position

7. Replace Photocell

8. Check wiring connections (See Wiring

Diagrams, Page 7)

Heater will not operate, or motor runs

for short time. Lamp flickers and LED

display shows “E1”

1. No paraffin in fuel tank

2. Incorrect pump pressure

3. Corroded Spark Plug or incorrect plug

gap.

4. Dirty Fuel Filter

5. Dirty Nozzle

6. Moisture in Fuel/Fuel Tank

7. Improper electrical connection

between Transformer and Circuit

Board

8. Ignitor Wire not connected to Spark

Plug

9. Defective Ignitor

1. Fill tank with fresh paraffin

2. Adjust Pump Pressure

3. Clean/replace Spark Plug

4. Clean/replace Fuel Filter

5. Clean/replace Nozzle

6. Rinse out fuel tank with clean fresh

paraffin

7. Inspect all electrical connections. See

Wiring Diagrams

8. Re-attach Ignitor wire to Spark Plug

9. Replace Ignitor

Fan does not operate when heater is

plugged in and Power Switch is in the

“ON” position. The lamp is flickering

or on and LED Display shows “E1” or

“E2”

1. Thermostat is set too low (Does not

apply to ST-45-KFA-E)

2. Broken electrical connection between

Main PCB and motor

1. Rotate thermostat to a higher setting

2. Inspect all electrical connections. See

Wiring Diagrams (Page 7)

Lamp is flickering, and LED display

shows “E3”

1. Thermostat Switch has failed 1. Replace Thermostat Switch

Poor Combustion and / or excess soot

production

1. Dirty Input, Output or Lint Filter

2. Dirty Fuel Filter

3. Poor quality of fuel

4. PSI is too high or too low

1. Clean/replace Air Filter

2. Clean/replace Fuel Filter

3. Be sure fuel is not contaminated or old

4. Use proper pressure

Heater does not turn on and the lamp

is not lit

1. Temperature limit sensor has

overheated

2. No electrical power

3. Fuse Blown

4. Improper electrical connection

between Temperature Limit Sensor

and Circuit Board

1. Push Power Switch to “OFF” and allow

heater to cool for 10 minutes. Push

Power Switch to back to “ON”

2. Check power cord and extension cord

to insure of proper connection. Test

power supply

3. Check/replace Fuse

4. Inspect all electrical connections.

Wiring Diagrams (Page 7)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley ST-125T-KFA-E Seite 80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info