Bedienungsanleitung Stanley STBS720 (Seite 8 von 11) (Englisch)

720735

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Operation

Using your belt sander (FIG. I)

Always hold belt sander ﬁrmly with both hands while sanding

as shown in FIG. I.

Note: that sander bail handle can be adjusted to three

different positions as previously discussed.

Switch (FIG. J and K)

To start your belt sander, depress the on/off switch as

shown in FIG. J. To stop your belt sander release the on/ off

switch.

For continuous operation, depress the on/off switch then

depress the lock-on button (FIG. K) and release the on/off

switch. To stop your belt sander, depress the on/off switch to

release the lock-on button. Release the on/off switch.

Handy Hints

• Always start your belt sander before it is in contact with

the workpiece and do not switch it off until after it has

been lifted from the workpiece.

• Always hold your belt sander with two hands.

• Where possible, clamp the workpiece to a work bench or

similar sturdy surface.

• Use the correct grit sanding belt for your application.

The following is a suggested list of belt grits to use with

different materials.

Material Belt Grit

Solid Wood 80

Veneer 150

Chipboard 60/80

Plastics 100

Steel 80 (remove dust bag)

Paint Removal 40/60

Balsa Wood 100

Acrylic 100

Tool Care And Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regular cleaning.

Never apply excessive force when you use your belt sander.

Too much force can result in an overload and cause damage

to the motor or the workpiece. If your belt sander becomes

too hot, operate it without load for 2 minutes. Always keep

the air cooling vents clear. To clean your belt sander,

proceed as follows:

Warning! To prevent accidental operation, turn

off and unplug sander before performing the

following operations. Failure to do this could

result in serious personal injury.

• Use a clean dry paint brush to clear vents and ducts.

• Clean the housings using a clean damp cloth (do not

use solvents, gas or turpentine.)

Important! To assure product SAFETY and

RELIABILITY, repairs, maintenance and

adjustment should be performed by authorized

service centers or other qualiﬁed service personnel, always

using identical replacement parts.

Accessories

The performance of your tool depends on the accessory

used. STANLEY accessories are engineered to high quality

standards and designed to enhance the performance of your

tool. By using these accessories you will get the very best

from your tool.

Use only 3” x 21” (76 x 533mm) sanding belts.

Recommended accessories for use with your tool are

available at extra cost from your local dealer or authorized

service center.

Notes

• STANLEY's policy is one of continuous improvement to

our products and, as such, we reserve the right to

change product speciﬁcations without prior notice.

• Standard equipment and accessories may vary by

country.

• Product speciﬁcations may differ by country.

• Complete product range may not be available in all

countries.

• Contact your local STANLEY dealers for range

availability.

ENGLISH (Original instructions)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STBS720 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info