Bedienungsanleitung Stanley STCD1081B2 (Seite 8 von 13) (Englisch)

720472

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

The charging indicator (11) will ﬂash green continuously

(slowly).

The charge is complete when the charging indicator (11)

lights green continuously. The charger and the battery can

be left connected indeﬁnitely with the LED illuminated. The

LED will change to ﬂashing green (charging) state as the

charger occasionally tops up the battery change. The

charging indicator (11) will be lit as long as the battery is

connected to the plugged-in charger.

• Charge discharged batteries within 1 week. Battery life

will be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indeﬁnitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the

charging indicator (11) will ﬂash red at a fast rate. Proceed

as follows:

• Re-insert the battery (5).

• If the charging indicators continues ﬂashing res at a fast

rate, use a different battery to determine if the charging

process works properly.

• If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

• If the new battery gives the same indication as the

original battery, take the charger to be tested at an

authorised service centre.

Note: It may take as long as 60 minutes to determine

that the battery is defective. If the battery is too hot or

too cold, the LED will alternately blink red, fast and

slow, one ﬂash at each speed and repeat

Selecting the direction of rotation (FIG. E)

For drilling and for tightening screws, use forward

(clockwise) rotation. For loosening screws or removing a

jammed drill bit, use reverse (counterclockwise) rotation.

• To select forward rotation, push the forward/reverse

slider (2) to the left.

• To select reverse rotation, push the forward/reverse

slider to the right.

• To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the torque

This tool is ﬁtted with a collar to set the torque for various

screwdriving and drilling applications. Large screws and hard

workpiece materials require a higher torque setting than

small screws and soft workpiece materials. For the deﬁnition

of the symbol refer to the listing below.

• For drilling in wood, metal and plastics, set the torque

adjustment collar (4) to the symbol.

• For screwdriving, set the collar to the desired setting. If

you do not yet know the appropriate setting, proceed as

follows:

- Set the torque adjustment collar (4) to the lowest

torque setting.

- Tighten the ﬁrst screw.

- If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the

correct setting. Use this setting for the remaining

screws.

Speed selector

• For drilling in steel and for screwdriving applications,

slide the speed selector (8) towards the rear of the tool

(1st gear).

• For drilling in materials other than steel, slide the speed

selector (8) towards the front of the tool (2nd gear).

Drilling/screwdriving

• Select forward or reverse rotation using the

forward/reverse slider (2).

• To switch the tool on, press the switch (1). The tool

speed depends on how far you press the switch.

• To switch the tool off, release the switch.

LED work light

The LED work light (7) is activated automatically when the

trigger is depressed. The LED work light will illuminate when

the trigger is partially depressed, before the unit begins

running.

ENGLISH (Original instructions)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STCD1081B2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info