Bedienungsanleitung Stanley STDG5006 (Seite 5 von 11) (Englisch)

720783

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

i. Wear personal protective equipment Depending on

application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping ﬂying debris generated by various operations.

The dust mask or respirator must be capable of ﬁltrating

particles generated by your operation. Prolonged

exposure to high intensity noise may cause hearing loss.

j. Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may ﬂy away and

cause injury beyond immediate area of operation

k. Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a “live” wire

may make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

l. Always hold the tool ﬁrmly in your hand(s) during

the start-up. The reaction torque of the motor, as it

accelerates to full speed, can cause the tool to twist.

m. Use clamps to support workpiece whenever

practical. Never hold a small workpiece in one

hand and the tool in the other hand while in use.

Clamping a small workpiece allows you to use your

hand(s) to control the tool. Round material such as

dowel rods, pipes or tubing have a tendency to roll while

being cut, and may cause the bit to bind or jump toward

you.

n. Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged and

your hand or arm may be pulled into the spinning

accessory.

o. Never lay the power tool down until the accessory

has come to a complete stop. The spinning

accessory may grab the surface and pull the power tool

out of your control.

p. After changing the bits or making any

adjustments, make sure the collet nut, chuck or

any other adjustment devices are securely

tightened. Loose adjustment devices can unexpectedly

shift, causing loss of control, loose rotating components

will be violently thrown.

q. Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

r. Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

s. Do not operate the power tool near ﬂammable

materials. Sparks could ignite these materials.

t. Do not use accessories that require liquid

coolants. Using water or other liquid coolants may result

in electrocution or shock.

Further Safety Instructions For All

Operations

Kickback And Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, sanding band, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the accessory’s

rotation.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either

jump toward or away from the operator, depending on

direction of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

a. Maintain a ﬁrm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. The operator can control kickback forces, if

proper precautions are taken.

b. Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

c. Do not attach a toothed saw blade. Such blades

create frequent kickback and loss of control.

ENGLISH

(Original instructions)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STDG5006 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info