Bedienungsanleitung Stanley STDR5206 (Seite 6 von 12) (Englisch)

720427

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

• Always wear eye protection. Any power tool can throw

foreign objects into your eyes and cause permanent eye

damage. ALWAYS wear safety goggles (not glasses) that

comply with ANSI safety standard Z87.1. Everyday

glasses have only impact resistant lenses. They ARE

NOT safety glasses

Warning! Glasses or goggles not in compliance

with ANSI Z87.1 could cause serious injury when

they break.

• Never use the drywall screwdriver to drive screws other

than drywall screws. The drywall screwdriver and the

screwdriver bits are designed speciﬁcally for driving

drywall screws.

• Only use screwdriver bits that are designed for use with

this tool.

• Always keep hands out of the path of the drywall screw.

Avoid awkward hand positions where a sudden slip could

cause your hand to move into the path of the saw blade.

• Make sure there are no nails or foreign objects in the

part of the workpiece to be cut or sanded.

• To avoid injury from accidental starting, always remove

the plug from the power source before installing or

removing a screwdriver bit or when adjusting the depth

control.

• Always check the wall area where screws will be driven

to be sure there are no hidden electrical wires in the

area.

• Never leave the Lock-on button ON. Before plugging the

tool into the power source, make sure the lock-on button

is OFF.

General Safety Warnings

Warning! Wear a dust mask that is designed to be

used when operating a power tool in a dusty

environment.

Warning! Dust that is created by power sanding,

sawing, grinding, drilling, and other construction

activities may contain chemicals that are known to

cause cancer, birth defects, or other genetic abnormalities.

These chemicals include:

• Lead from lead-based paints

• Crystalline silica from bricks, cement, and other masonry

products

• Arsenic and chromium from chemically treate lumber

The level of risk from exposure to these chemicals varies,

according to how often this type of work is performed. In

order to reduce exposure to these chemicals, work in a

well-ventilated area, and use approved safety equipment,

such as a dust mask that is speciﬁcally designed to ﬁlter out

microscopic particles.

Safety Extension Cord

Warning! Keep the extension cord clear of the

working area. Position the cord so it will not get

caught on the workpiece, tools or any other obstructions

while you are working with the power tool.

Make sure any extension cord used with this tool is in good

condition. When using an extension cord, be sure to use one

of heavy enough gauge to carry the current the tool will

draw. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating.

Be sure your extension cord is properly wired and in good

condition. Always replace a damaged extension cord or

have it repaired by a qualiﬁed electrician before using it.

Protect your extension cord from sharp objects, excessive

heat and damp or wet areas.

Use a separate electrical circuit for your power tools. This

circuit must not be less than 14 gauge wire and should be

protected with either a 15 A time delayed fuse or circuit

breaker. Before connecting the power tool to the power

source, make sure the switch is in the OFF position and the

power source is the same as indicated on the nameplate.

Running at lower voltage will damage the motor.

Contents

Carefully unpack the drywall screwdriver. Compare the

contents against the “Drywall screwdriver components” chart

below.

Assembly and Operating

Warning! To avoid ﬁre or toxic reaction, never use

gasoline, naphtha, acetone, lacquer thinner or

similar highly volatile solvents to clean the tool.

Forward/Reverse switch (Fig. B)

The forward/reverse switch (4) is conveniently mounted in

front of the variable speed trigger switch (5). To make the

screwdriver rotate clockwise for driving screws, push the

forward/reverse switch (4) to the left. To make the

screwdriver rotate counter-clockwise to remove screws,

push the forward/reverse switch (4) to the right.

(Original instructions)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STDR5206 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info