Bedienungsanleitung Stanley STDR5510C (Seite 6 von 10) (Englisch)

720428

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

ENGLISH

(Original instructions)

Warning! To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a sudden reaction.

Drilling in metal

Start drilling with slow speed and increase to full power while

applying ﬁrm pressure on the tool. A smooth even ﬂow of

metal chips indicates the proper drilling rate. Use a cutting

lubricant when drilling metals. The exceptions are cast iron

and brass which should be drilled dry.

Note: Large [5/16" (8 mm)] holes in steel can be made

easier if a pilot hole [5/32" (4 mm)] is drilled ﬁrst.

Drilling in wood

Start drilling with slow speed and increase to full power while

applying ﬁrm pressure on the tool. Holes in wood can be

made with the same twist drills used for metal. These bits

may overheat unless pulled out frequently to clear chips

from the ﬂutes. Work that is apt to splinter should be backed

up with a block of wood.

Accessories

The performance of your tool depends on the accessory

used.STANLEY accessories are engineered to high quality

standards and designed to enhance the performance of your

tool. By using these accessories you willget the very best

from your tool.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regular cleaning.

Warning! Before performing any maintenance, switch off

and unplug the tool.

• Regularly clean the ventilation slots in your tool using a

soft brush or dry cloth.

• Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Remarks

• STANLEY's policy is one of continuous improvement to

our products and as such, we reserve the right to modify

product speciﬁcations without prior notice.

• Standard equipment and accessories may vary by

country.

• Product speciﬁcations may differ by country.

The vibration emission level given in this information sheet

has been measured in accordance with a standardised test

given in EN 60745 and may be used to compare one tool

with another. It may be used for a preliminary assessment of

exposure.

Warning: The declared vibration emission level

represents the main applications of the tool.

However if the tool is used for different

applications, with different accessories or poorly maintained,

the vibration emission may differ. This may signiﬁcantly

increase the 1.5exposure level over the total working period.

An estimation of the level of exposure to vibration should

also take into account the times when the tool is switched

off or when it is running but not actually doing the job. This

may signiﬁcantly reduce the exposure level over the total

working period.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and

the accessories, keep the hands warm, organisation of work

patterns.

(sound pressure) dB(A) 84

(sound pressure uncertainty) dB(A) 3

(sound power) dB(A) 95

(sound power uncertainty) dB(A) 3

Vibration emission value a

Check (

Drilling

)

Main handle (a

)

= m/s²

5.1

Uncertainty K = m/s² 1.5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STDR5510C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info