ENGLISH
(Original instructions)
8
P
1 Angle
1 Guard
1 Side handle
1 Flange set
1 T
1 Instruction manual
• Check for damage to the tool, parts or accessories which
may have occurred during transport.
• T
manual prior to operation.
FEA
This appliance includes some or all of the following features.
W Never modify the power tool or any part
of it. Damage or personal injury could result.
1. Switch
2. Spindle lock
3. Guard
4. Side handle
Purpose of design
This angle grinder is designed especially for grinding.
Do not use sandpaper discs and grinding wheels other than
those with depressed center
Do not use the tool in wet conditions or environments in the
presence of flammable liquids or gases.
This angle grinder is a professional power tool.
Do not allow children to come in contact with this tool.
Inexperienced operators are required to use this tool under
supervision.
ASSEMBL
W
personal injury
and disconnect all plugs before adjusting or
removing/installing any accessory Before
reassembling
switch to make sure the tool is already switched off.
Attaching and removing the wheel guard (Fig. B)
W
personal injury
and disconnect all plugs before adjusting or
removing/installing any accessory Before
reassembling
switch to make sure the tool is already switched off.
Attaching the guard
1. Place the angle grinder on a work bench, groove facing
up.
2. Bring
the gear housing.
3. Turn the guard (3) counterclockwise by 150 degrees.
4. Make sure that the screws (12) are tightened.
Removing the guard
1. Loosen the screws (12) on the guard collar
2. Pull up the guard (3).
W: Do not operate the tool when the safety
guard is not in place.
Fitting and removing a grinding wheel (Fig C1, C2, C3)
W: Do not use damaged grinding wheels.
1. Place the tool on a work bench, guard up.
2. Fit the inner flange (5) correctly onto the spindle (6)
(Fig. C1).
3. Place the disc (7) on the
disc with a raised center
(8) is facing the flange (5).
4. Screw the out flange (9) onto the spindle (6) (Fig. C3)
- the ring on the flange (9) must face towards the disc
when fitting a grinding disc (C3-A)
- the ring on the flange (9) must face away from the
disc when fitting a cutting disc (C3-B)
LABELS ON TOOL
The label on your tool may include the following symbols:
Position of date code
The date code, which also includes the year of manufacture,
is printed into the housing.
Example:
2017 XX JN
Y
WARNING!
must read the instruction manual before use.
Wear ear protection.
Wear a dust mask.
Wear safety glasses or goggles.
V V Direct Current
A Amperes n
0
No-Load Speed
Hz Hertz Class II Construction
W Watts
Earthing T
min minutes
Safety
Alternating
Current
/min.
Revolutions or
Reciprocation per
minute
edge of wheel has been rounded off, you are free to operate the
grinder in either the
Starting and stopping (Fig A)
W Before using the tool, check whether the
handle is tightened securely
working normally
Before plugging in the tool to the power supply
switch is in the OFF position.
W Do not switch the tool on or off while under
load conditions.
Proper hand position (Fig G)
W T
AL
W T
AL hold securely in anticipation of a sudden
reaction.
Proper hand position requires one hand
with the other hand on the body of the tool, as shown in figure G.
Switch
CAUTION:
tool at start up and during use and until the wheel or accessory stops
rotating.
laying the tool down.
NOTE: T
on or off while under load conditions.
full speed before touching the work surface. Lift the tool from the
surface before turning the tool off. Allow the tool to stop rotating
before putting it down.
W Before connecting the tool to a power supply
be
the front part of the switch and releasing. Ensure the
slider switch is
any interruption in power supply to the tool, such as the
activation of a ground fault interrupter
circuit
the slider switch is locked on when the power is
connected, the tool will start unexpectedly
Lock-On feature of the switch
Press the trigger (1), the tool will start. Keep pressing the trigger
then slide trigger (1) to
“on“
tool will stop running.
Explanation: Before coming into contact with the object you
are working on, make sure the abrasive wheel is turning at
maximum speed. Before turning off the tool, lift the tool up
from the object you are working on.
CAUTION: Make sure the abrasive wheel is completely
stopped before putting down the tool.
(Original instructions) ENGLISH
9
5. Press
in position (Fig. C2).
6. Tighten the flange (9) with the two-pin spanner supplied.
7. Release the spindle lock.
8. T the flange (9) with the two-pin
spanner
W: Do not use a damaged disc.
Attaching the Side Handle (Fig D)
WBefore using the tool, check that the handle
is tightened securely
W The side handle should always be used to
maintain control of the tool at all times.
Screw
either side of the gear case.
Preparation before use
• Attach the safety guard and appropriate abrasive or grinding
wheels. not abrasive or grinding wheels are
worn.
• Make sure that the inner and outer flanges are attached
correctly
• Make sure that the abrasive or grinding wheels are rotating in the
direction of the arrows on the accessories and tool.
VOL
In
power supply conditions, other equipment may be affected. If the
system impedance of the power supply is lower than 0.175Ω ,
disturbances are unlikely to occur
USE (Fig F)
W Always observe the safety instructions and
applicable regulations.
W
personal injury
disconnect all plugs before adjusting or
removing/installing any accessory Before
reassembling the tool, press and release the trigger
switch to make sure the tool is already switched off.
• Make sure all materials to be grinded are secured in position.
• Apply slight pressure to the tool. Do not apply side pressure to
the abrasive disc.
• Avoid the becomes let spin a
minutes with no load.
1. Be sure to hold the tool tightly with both hands (one hand on
housing, on Start and
grinding wheel on the workpiece.
2. Keep the
against the surface of the workpiece.
3. When wheel,
the B direction, otherwise, it will cut into the workpiece. When the
