Bedienungsanleitung Stanley STHM5 (Seite 6 von 12) (Englisch)

720457

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

(Original instructions)

These are:

• Injuries caused by touching any rotating/moving parts.

• Injuries caused when changing any parts, blades or

accessories.

• Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

• Impairment of hearing.

• Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

• If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised STANLEY Service Centre

in order to avoid a hazard.

Using an extension cable

If it is necessary to use an extension cable, please used an

approved extension cable that ﬁts the tool’s power input

speciﬁcations (please refer to the technical data). The

minimum cross-sectional area of the conducting wire is 1.5

sq. mm. Cables should be untangled before reeling up.

Features

This tool includes some or all of the following features.

a. Side Handle

b. Switch

c. Barrel cover

d. Tool sleeve

e. Lube oil-injection inlet

Assembly and adjustment

Warning! To reduce the risk of injury, turn

unit off and disconnect machine from power

source before installing and removing

accessories, before adjusting or changing set-ups or when

making repairs. Be sure the trigger switch is in the OFF

position. An accidental start-up can cause injury.

Inserting and removing SDS Max accessories (ﬁg. 1)

This tool uses SDS Max accessories (refer to the inset in

ﬁgure 1 for a cross-section of an SDS Max bit shank). We

recommend to use professional accessories only.

1. Clean and grease the bit shank.

2. Insert the bit shank into the bit holder/tool sleeve (d).

3. Push the bit down and turn it slightly until it ﬁts into the

slots.

4. Pull on the bit to check if it is properly locked. The

hammering function requires the bit to be able to move

axially several centimetres when locked in the tool

holder.

5. To remove a bit pull back the tool holder/locking sleeve

(d) and pull out the bit.

Warning: Always wear gloves when you change

accessories. The exposed metal parts on the

tool and accessory may become extremly hot

during operation.

Fitting the side handle (ﬁg. 1)

The side handle (a) can be ﬁtted to suit both RH- and

LH-users.

Warning: Do not use the tool without the side

handle properly assembled.

1. Loosen the side handle.

2. For RH-users: Slide the side handle clamp over the

collar behind the tool holder, handle at the left. For

LH-users: Slide the side handle clamp over the collar

behind the tool holder, handle at the right.

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example:

2014 XX JN

Year of manufacturing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STHM5 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info