Bedienungsanleitung Stanley STHR263 (Seite 6 von 10) (Englisch)

720460

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

ENGLISH

• Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

• Impairment of hearing.

• Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

• If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised STANLEY Service Centre

in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Drilling mode selector

5. Tool holder

6. Side handle

7. Depth stop

8. Depth stop lock button

Assembly

Warning! Before assembly, make sure that the tool

is switched off and unplugged.

Fitting the side handle

• Turn the grip counterclockwise until you can slide the

side handle (6) onto the front of the tool.

• Rotate the side handle into the desired position.

• Tighten the side handle by turning the grip clockwise.

Fitting an accessory (ﬁg. A)

• Clean and grease the shank (9) of the accessory.

• Pull back the sleeve (10) and insert the shank into the

tool holder (5).

• Push the accessory down and turn it slightly until it ﬁts

into the slots.

• Pull on the accessory to check if it is properly locked.

The hammering function requires the accessory to be

able to move axially several centimetres when locked in

the tool holder.

• To remove the accessory, pull back the sleeve (10) and

pull out the accessory.

Use

Wear a dust mask

Warning! Let the tool work at its own pace. Do not

overload.

Warning! Before drilling into walls, ﬂoors or ceilings,

check for the location of wiring and pipes

Selecting the operating mode (ﬁg. B)

The tool can be used in three operating modes. Press in the

button (11) and rotate the drilling mode selector (4) towards

the required position, as indicated by the symbols.

Drilling

• For drilling in steel, wood and plastics, set the operating

mode selector (4) to the position.

Hammer drilling

• For hammer drilling in masonry and concrete, set the

operating mode selector (4) to the position

• When hammering, the tool should not bounce and run

smoothly. If necessary, increase the speed.

(Original instructions)

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example:

2014 XX JN

Year of manufacturing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STHR263 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info