Bedienungsanleitung Stanley STHR323 (Seite 6 von 11) (Englisch)

720462

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

ENGLISH

(Original instructions)

Residual risks.

Additional residual risks may arise when using the tool

which may not be included in the enclosed safety warnings.

These risks can arise from misuse, prolonged use etc. Even

with the application of the relevant safety regulations and

the implementation of safety devices, certain residual risks

can not be avoided. These include:

• Injuries caused by touching any rotating/moving parts.

• Injuries caused when changing any parts, blades or

accessories.

• Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

• Impairment of hearing.

• Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

• If the supply cord is damaged, it must be replaced by

the manufacturer or an authorised STANLEY Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. On/Off switch

2. Speed selector dial

3. Drilling mode selector

4. Operating mode selector

5. Tool holder

6. Side handle

7. Depth stop

8. Grease cap

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle (ﬁg. A)

• Turn the grip counterclockwise until you can slide the

side handle (6) onto the front of the tool as shown.

• Rotate the side handle into the desired position.

• Tighten the side handle by turning the grip clockwise.

Fitting and setting the depth stop (ﬁg. A)

• Slacken the knob (9).

• Insert the depth stop (7) into the mounting hole as

shown.

• Set the depth stop (7) to the desired position. The

maximum drilling depth is equal to the distance between

the tip of the drill bit and the front end of the depth stop.

• Tighten the knob (9).

Fitting an accessory (ﬁg. B - D)

• Clean and grease the shank (10) of the accessory.

• Pull back the sleeve (11) and insert the shank into the

tool holder (5).

• Push the accessory down and turn it slightly until it ﬁts

into the slots.

• Pull on the accessory to check if it is properly locked.

The hammering function requires the accessory to be

able to move axially several centimetres when locked in

the tool holder.

• To remove the accessory, pull back the sleeve (11) and

pull out the accessory.

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example:

2014 XX JN

Year of manufacturing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STHR323 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info