Bedienungsanleitung Stanley STHT1-12184 -APC-BN (Seite 9 von 130) (Alle Sprachen)

622189

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

TECHNICAL DATA:

Please look at the technical table marked * at the end of this manual.

PROBLEM CAUSE CORRECTION

Failure to cycle Air supply restriction Check air supply equipment

Tool dry, lack of lubrication Use STANLEY BOSTITCH Air Tool Lubricant

Worn head valve O-rings (if present) Replace O-rings

Broken cylinder cap spring Replace cylinder cap spring

Head valve (if present) stuck in cap Disassemble/Check/Lubricate

Lack of power; slow to cycle Air pressure too low Check air supply equipment

Tool dry, lacks lubrication Use STANLEY BOSTITCH Air Tool Lubricant

Broken cylinder cap spring Replace cylinder cap spring

O-rings/seals cut or cracked Replace O-rings/seals

Exhaust blocked Check bumper, head valve spring, muffler

Trigger assembly worn/leaks Replace trigger assembly

Cylinder sleeve not seated correctly on bottom bumper Disassemble to correct

Head valve dry Disassemble/lubricate

Trigger valve housing leaking air. O-ring cut or cracked Replace O-ring

Trigger valve stem leaks air O-rings/seals cut or cracked Replace O-rings/seals

Frame/nose leaks air O-ring or gasket is cut or cracked Replace O-ring or gasket

Bumper cracked/worn Replace bumper

Frame/cap leaks air Damaged gasket or seal Replace gasket or seal

Cracked/worn head valve bumper Replace bumper

Loose cap screws Tighten and recheck

Skipping fasteners; intermittent feed Worn bumper Replace bumper

Air restriction/inadequate air flow through quick

disconnect socket and plug

Replace quick disconnect fittings

Worn piston O-ring (if present) Replace O-ring, check driver

Tool dry, lacks lubrication Use STANLEY BOSTITCH Air Tool Lubricant

Damaged pusher spring Replace spring

Low air pressure Check air supply system to tool

Loose magazine nose screws Tighten all screws

Fasteners too short for tool Use only recommended fasteners

Bent fasteners Discontinue using these fasteners

Wrong size fasteners Use only recommended fasteners

Leaking head cap gasket Tighten screws/replace gasket

Trigger valve O-ring cut/worn Replace O-ring

Broken/chipped driver Replace driver (check piston O-ring)

Dry/dirty magazine Clean/lubricate use STANLEY BOSTITCH Air Tool Lubricant

Worn magazine Replace magazine

Fasteners jam in tool Driver channel worn Replace nose/check door

Wrong size fasteners Use only recommended fasteners

Bent fasteners Discontinue using these fasteners

Loose magazine/nose screws Tighten all screws

Broken/chipped driver Replace driver (check piston O-ring)

A Length mm. K Air consumption per shot @ 5.6 Bar

B Height mm. L Activation type

C Width mm. M Summer lubricant

D Weight Kg. N Winter lubricant

E Noise Lpa, 1s, d O O-ring lubricant

F Noise Lwa, 1s, d P Fastener Name

G Noise Lpa, 1s, 1m Q Dimensions mm.

H Vibration m/s

R Head/crown

I P max Bar S Magazine capacity

J P min Bar T New Driver Length mm.

U Max. Depth Inside Piston mm.

TROUBLESHOOTING

l Disconnect the tool from the air supply and empty the magazine completely before proceeding.

l If the problem cannot be resolved using the guide below, Contact your nearest Stanley representative or distributor.

FT72124-a-0611_Tool_Manual_AW.indd 9 05/07/2011 17:01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STHT1-12184 -APC-BN Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info