Bedienungsanleitung Stanley STHT1-77341 (Seite 12 von 210) (Alle Sprachen)

720751

Zoom out

Zoom in

Vorherige Seite

1/210

Nächste Seite

STHT77341

Applications

Plumb Transfer

• Using the vertical laser beam, establish a vertical

reference plane.

• Position thve desired object(s) until they are aligned

with the vertical reference plane to ensure object(s)

are plumb.

Level Transfer

• Using the horizontal laser beam, establish a horizontal

reference plane.

• Position the desired object(s) until they are aligned

with the horizontal reference plane to ensure object(s)

are level.

Square

• Using the vertical and horizontal laser beams, establish

a poing where the two beams cross.

• Position the desired object(s) until they are aligned with

both the vertical and horizontal laser beams to ensure

objects(s) are square.

Manual Mode

(See ﬁgures

)

• Disables self-leveling function and allows laser unit to

project a rigid laser beam in any orientation.

Batteries and Power

Battery Installation / Removal (See ﬁgure

)

Laser Tool

• Turn laser tool to battery door and open.

• Install / Remove batteries. Orient batteries correctly

when placing into battery compartment.

• Close battery door. Be sure that the door has been

closed securely.

WARNING:

• Pay close attention to the battery holder’s (+)

and (-) markings for proper battery insertion.

Batteries must be of same type and capacity. Do

not use a combination of batteries with different

capacities remaining.

Set Up

Laser Tool

• Place laser tool on a ﬂat, stable surface.

• If using the auto leveling feature move the pendulum /

transport lock to the unlocked position. The laser tool

must then be positioned in its upright position on a

surface that is within the speciﬁed compensation range.

• The laser tool can be placed in any orientation and be

functional only when the pendulum / transport lock is in

the locked position.

Mounting on Accessories

• Position accessory in a place where it will not be easily

disturbed and near the central location of the area to

be measured.

• Set up the accessory as required. Adjust positioning to

be sure accessory base is near horizontal (within laser

tools compensation range).

• Mount the laser tool to the accessory using the

appropriate fastening method to be used with such

accessory / laser tool combination.

CAUTION:

• Do not leave the laser tool unattended on an

accessory without fully tightening the fastening

screw. Failing to do so may lead to the laser tool

falling and sustaining possible damage.

NOTE:

• It is best practice to always support laser tool with

one hand when placing or removing laser tool from an

accessory.

• If positioning over a target, partially tighten the fastener,

align laser tool, and then fully tighten.

Cross90 GB_STHT77341.indd 12 01/07/2013 09:50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STHT1-77341 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info