Bedienungsanleitung Stanley STHT77502-1 (Seite 14 von 238) (Alle Sprachen)

720754

Zoom out

Zoom in

Vorherige Seite

1/238

Nächste Seite

Using the Laser with the Bracket

A bracket (Figure

) is included with the laser so

you can easily attach the laser to a stud, ceiling grid,

or pole.

Securely attach the laser to the bracket.

• Using the 1/4-20 thread on the bottom, side,

or back of the laser (Figure

), position the

laser on the 1/4-20 thread on the bracket arm

(Figure

• Turn the laser knob (Figure

) clockwise

to lock the laser on the 1/4-20 thread on the

bracket arm.

If needed, change the height or position of the

laser on the bracket.

• Turn the adjustment knob (Figure

)

counter-clockwise to loosen the bracket arm.

• Slide the bracket arm up or down to the desired

height (Figure

). To change the bracket

from 90° to 180°, slide the bracket arm to the

top of the bracket and then flip the arm to the

right (Figure

• Turn the adjustment knob (Figure

)

clockwise to lock the bracket arm in place.

Use the bracket’s clamp (Figure

) to hold

the laser in place on a stud, ceiling grid, or pole.

• If necessary, rotate the clamp so it is positioned

at the correct angle for attaching to the object.

While holding the bracket arm with one hand,

use your other hand to turn the clamp

(Figure

• Position the bracket’s clamp around the stud,

ceiling grid, or pole.

• Turn the clamp knob (Figure

) clockwise

until the clamp is tight around the object and

the bracket is held in place.

Using the Laser with Other

Accessories

WARNING:

Since accessories other than those offered

by STANLEY have not been tested with this

laser, use of such accessories with this laser

could be hazardous.

Only use STANLEY

accessories that are

recommended for use with this model. Accessories

that may be suitable for one laser may create a risk of

injury when used with another laser.

The laser is equipped with a 1/4-20 female thread on

the bottom, side, and back (Figure

)

to accommodate current or future STANLEY

accessories.

Other recommended accessories for use with this

laser are available at extra cost from your local dealer

or authorized service center. If you need assistance

locating any accessory, please contact your nearest

STANLEY service center or visit our website:

http://www.STANLEY.com.

Maintenance

• When the laser is not in use, clean the exterior parts

with a damp cloth, wipe the laser with a soft dry

cloth to make sure it is dry, and then store the laser

in the kit box provided.

• Although the laser exterior is solvent resistant,

NEVER use solvents to clean the laser.

• Do not store the laser at temperatures below -5 ˚F

(-20 ˚C) or above 140 ˚F (60 ˚C).

• To maintain the accuracy of your work, check the

laser often to make sure it is properly calibrated.

• Calibration checks and other maintenance repairs

may be performed by STANLEY service centers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STHT77502-1 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info