Bedienungsanleitung Stanley STSC2135 (Seite 8 von 12) (Englisch)

720789

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Maintenance

Your STANLEY power tool has been designed to operate

over a long period of time with a minimum of

maintenance.Continuous satisfactory operation depends

upon proper tool care and regular cleaning.Your tool is not

user-serviceable. Take the tool to an authorized STANLEY

repair agent. This tool should be serviced at regular

intervals or when showing a noticeable change in

performance.

Lubrication

STANLEY power tools are properly lubricated at the factory

and are ready for use. Tools should be re-lubricated

regularly , depending on usage. This lubrication should only

be attempted by trained power tool repair persons, such as

those at STANLEY service centers or by other qualiﬁed

service personnel. Closed-type, grease-sealed ball bearings

are used throughout. These bearings have sufﬁcient

lubricationpacked in them at the factory to last the life of the

chop saw.

Cleaning

Warning: unplug the tool before you use a cloth

to clean the housing.With the motor running,

blow dirt and dust out of all air vents with dry air

at least once a week. Wear safety glasses when performing

this. Exterior plastic parts may be cleaned with a damp cloth

and mild detergent. Although these parts are highly solvent

resistant, NEVER use solvents.

Blowing dust and grit out of the main housing by means of

an air hose is recommended and may be done as often as

dirt is seen collecting in and around the air vents. Always

wear proper eye and respiratory protection.

Tool care

Avoid overloading the machine.Overloading will result in a

considerable reduction in speed and efﬁciency and the unit

will become hot. In this event,run the machine at no load for

a minute or two until cooled to normal working temperature

by the built in fan. Switching your machine on and off whilst

under load will considerably reduce the life of the switch.

Important

To ensure product SAFETY and RELIABILITY, repairs,

maintenance and adjustment (other than those listed in this

manual) should be performed by authorized service centers

or other qualiﬁed organizations, always-using identical

replacement parts. Unit contains no user serviceable parts

inside.Blowing dust and grit out of the main housing by

means of an air hose is recommended and may be done as

often as dirt is seen collecting in and around the air vents.

Always wear proper eye and respiratory protection.

Note: Unit may be converted to a 3-wire twist lock cord set

at an authorized service center.

Notes

• STANLEY's policy is one of continuous improvement to

our products and, as such, we reserve the right

tochange product speciﬁcations without prior notice.

• Standard equipment and accessories may vary by

country.

• Product speciﬁcations may differ by country.

• Complete product range may not be available in all

countries.

• Contact your local STANLEY dealers for range

availability.

ENGLISH (Original instructions)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STSC2135 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info