Bedienungsanleitung Stanley STSM1510 (Seite 6 von 14) (Englisch)

720686

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

properly and perform its intended function—check for

alignment of moving parts, binding of moving parts,

breakage of parts, mounting and any other conditions

that may affect its operation. A guard or other part that is

damaged should be properly repaired or replaced. Do

not use tool if switch does not turn it on and off.

• NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it comes to a

complete stop.

• DO NOT OPERATE ELECTRIC TOOLS NEAR

FLAMMABLE LIQUIDS OR IN GASEOUS OR

EXPLOSIVE ATMOSPHERES. Motors in these tools

may spark and ignite fumes.

• USE PROPER EXTENSION CORDS. Make sure your

extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to

carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss of

power and overheating. The following table shows the

correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next

heavier gage. The smaller the gage number, the heavier

the cord.

Additional Safety Rules For Mitre Saws

CAUTION: FAILURE TO HEED THESE

WARNINGS MAY RESULT IN PERSONAL

INJURY AND SERIOUS DAMAGE TO THE SAW.

• DO-Protect electric supply line with at least a 15 ampere

time-delay fuse or a circuit breaker.

• Replace table insert when worn

• Use only saw blades recommended by the manufacturer

• Connect mitre saw to a dust connecting device when

sawing

• Take care when slotting

• DO-Make certain the blade rotates in the correct

direction and that the teeth at the bottom of the blade are

pointing to the rear of the mitre saw.

• DO-Be sure all clamp handles are tight before starting

any operation.

• DO-Be sure all blade and clamp washers are clean and

recessed sides of collars are against blade. Tighten

arbor screw securely.

• DO-Keep saw blade sharp.

• DO-Keep motor air slots free of chips and dirt.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

ENGLISH (Original instructions)

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example:

2014 XX JN

Year of manufacturing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STSM1510 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info