Bedienungsanleitung Stanley STSP125 (Seite 5 von 56) (Englisch, Französisch, Portugiesisch)

720790

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

(Original instructions)

installing the wheel, position yourself and

bystanders away from the plane of the rotating

wheel and run the power tool at maximum no load

speed for one minute. Damaged wheels will normally

break apart during this test time.

j) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and shop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping ﬂying

debris generated by various operations. The dust mask

or respirator must be capable of ﬁltrating particles

generated by your operation. Prolonged exposure to

high intensity noise may cause hearing loss.

k) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken wheel may ﬂy away and cause

injury beyond immediate area of operation.

l) Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a "live" wire

may make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

m) Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and

your hand or arm may be pulled into the spinning wheel.

n) Never lay the power tool down until the accessory

has come to a complete stop. The spinning wheel may

grab the surface and pull the power tool out of your

control.

o) Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

p) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

q) Do not operate the power tool near ﬂammable

materials. Sparks could ignite these materials.

r) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

Note: The above warning does not apply for power tools

speciﬁcally designed for use with a liquid system.

Further safety instructions for abrasive

cutting-off operations Kickback and related

warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel. Pinching or snagging causes rapid stalling of

the rotating wheel which in turn causes the uncontrolled

power tool to be forced in the direction opposite of the

wheel’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either

jump toward or away from the operator, depending on

direction of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

a) Maintain a ﬁrm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up. The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in line with the rotating

wheel. Kickback will propel the tool in direction opposite

to the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STSP125 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info