Bedienungsanleitung Stanley SW19 (Seite 9 von 24) (Englisch, Französisch)

720598

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

(Original instructions) ENGLISH

If there is a pilot light on the starter device, it should go out.

• Water jet control lever (20).

Warning! During operation the appliance must be

positioned as shown in Fig. D on a ﬁrm, stable surface.

Start-up (see Fig. D)

1. Turn on the water supply tap fully.

2. Release the safety catch (21).

3. Depress the gun trigger for a few seconds and start up the

appliance using the starter device (ON/I).

Warning! Before starting up the appliance check that it

is receiving water correctly; use of the appliance without

water will damage it. Do not cover the ventilation grilles when

the appliance is in use.

TSS Models - In TSS models with automatic delivery ﬂow

cut-o system:

a. When the gun trigger is released, the dynamic pressure

automatically cuts out the motor;

b. When the gun trigger is depressed, the automatic drop in

pressure starts the motor and the pressure is restored

after a very slight delay;

c. If the TSS is to function correctly all gun trigger releasing

and depressing operations, must be at least 4 - 5 seconds

apart.

To prevent damage to the appliance, do not allow it to operate

dry and check that it is properly supplied with water. For

models without TSS, to prevent damage to the appliance due

to an increase in water temperature, do not cut off the jet of

water for more than 5 minutes with the appliance running.

Stopping

1. Set the starter device switch on (OFF/0).

2. Depress the gun trigger and discharge the residual

pressure inside the pipes.

3. Engage the safety catch (21).

Restarting

1. Release the safety catch (21).

2. Depress the gun trigger and discharge the residual air

inside the pipes.

3. Set the starter device on (ON/I).

Storage

1. Turn o the water supply tap.

2. Discharge the residual pressure from the gun until all the

water has come out of the appliance.

3. Switch the appliance off (OFF/0).

4. Remove the plug from the socket.

5. Drain and wash out the detergent tank at the end of the

working session. To wash out the tank, use clean water

instead of the detergent.

6. Engage the gun safety catch (21).

Recommended cleaning procedure

Dissolve dirt by applying the detergent mixed with water to the

surface while still dry. When dealing with vertical surfaces

work from the bottom upwards. Leave the detergent to act for

1-2 minutes but do not allow the surface to dry. Starting from

the bottom, use the high pressure jet at a minimum distance of

30cm. Do not allow the rinse water to run onto unwashed

surfaces. In some cases, scrubbing with brushes is needed to

remove dirt. High pressure is not always the best solution for

good washing results, since it may damage some surfaces.

The ﬁnest adjustable nozzle jet setting or the rotopower

nozzle should not be used on delicate or painted parts, or on

pressurised components (e.g tyres, inﬂation valves, etc.).

Effective washing depends on both the pressure and volume

of the water used, to the same degree.

MAINTENANCE (Fig. E)

Any maintenance operations not covered by this chapter

should be carried out by an authorized sales and service

centre.

Warning! Always disconnect the plug from the power

socket before carrying out any work on the appliance.

Cleaning the nozzle

1. Disconnect the lance from the nozzle.

2. Remove any dirt deposits from the nozzle hole using the

tool (4).

Cleaning the ﬁlter

Inspect the inlet ﬁlter (8) and detergent ﬁlter (if ﬁtted) before

each use, and clean in accordance with the instructions if

necessary.

Unjamming the motor (On models with this feature)

In case of lengthy stoppages, limescale sediments may cause

the motor to seize. To unjam the motor, turn the drive shaft

with a tool.

End-of-season storage

reat the appliance with non-corrosive, non-toxic antifreeze

before storing it away for winter. Put the appliance in a dry

place, protected from frost.

STORAGE AND TRANSPORTATION (Fig. E)

Store the accessories as shown in Fig. E.

Transport the machine as shown in Fig. E.

HOW TO AVOID DAMAGING SURFACES

Warning!

• Using the appliance to wash tyres may damage the tyre

and can be dangerous.

• Never point the high pressure jet straight at the tyre.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SW19 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info