Bedienungsanleitung Stanley SW21 (Seite 8 von 24) (Englisch, Französisch)

720600

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISH (Original instructions)

Vehicle engines may be washed only if the dirty water is

disposed of as per regulations in force.

• Intake water temperature: See data plate on the

appliance.

• Intake water pressure: min. 0.1 MPa - max. 1 MPa.

• Operating ambient temperature: Above 0 °C.

The appliance is compliant with the IEC 60335-1 and IEC

60335-2-79 standards.

OPERATOR

The symbol illustrated in Fig. A identiﬁes the appliance’s

intended operator (professional or non-professional).

MAIN COMPONENTS (Fig. A)

1. Lance

2. Gun with safety catch

3. High pressure hose

4. Nozzle cleaning tool

5. Rotating nozzle kit

6. Nozzle

7. Adapter

8. Water ﬁlter

9. Detergent kit

10. Screws

11. Electric cable with plug

12. Wheels

13. Hose reel

14. Handle

15. Lever

16. Brackets

Starter device (19)

The starter device prevents accidental use of the appliance.

Caution! Safety devices:

Do not tamper with or adjust the safety valve setting.

• Safety valve and/or pressure limiting valve. The safety

valve is also a pressure limiting valve. When the gun

trigger is released, the valve opens and the water

recirculates through the pump inlet or is discharged onto

the ground.

• Thermostat valve (where ﬁtted) If the water temperature

exceeds the temperature set by the manufacturer, the

thermostat valve discharges the hot water and draws in an

amount of cold water equal to the amount of water

discharged, until the correct temperature is restored.

• Safety catch (21): prevents accidental spraying of water.

• Overload cutout: stops the appliance in case of overload.

INSTALLATION (Fig. B)

Assembly

Warning! All installation and assembly operations must

be performed with the appliance disconnected from the

mains power supply.

The assembly sequence is illustrated in Fig. B.

Fitting the rotating nozzle

The rotating nozzle kit delivers greater washing power. Use of

the rotating nozzle may cause a reduction in pressure of 25%

compared to the pressure obtained with the adjustable nozzle.

However, the rotating nozzle kit delivers greater washing

power due to the rotation of the water jet.

Electrical connection

Warning! Check that the electrical supply voltage and

frequency (V/Hz) correspond to those on the appliance

data plate (Fig. B8).

Use of extension cables: Use cables and plugs with “IPX5”

protection level. The cross-section of the extension cable

should be pro- portionate to its length; the longer it is, the

greater its cross-section should be.

Water supply connection

Caution! Only clean or ﬁltered water should be used for

intake. The delivery of the water intake tap should be

equal to that of pump capacity.

Place the appliance as close to the water supply system as

possible.

Connection points:

Water outlet (OUTLET)

Water inlet with ﬁlter (INLET)

Connection to the mains water supply

The appliance may only be connected directly to the mains

drinking water supply if the supply hose is ﬁtted with a

backﬂow preventer valve as per current regulations in force.

Make sure that the hose is at least Ø 13 mm, that it is

reinforced and that it is not more than 25 m long.

ADJUSTMENT INFORMATION (Fig. C)

• Adjusting the spray nozzle (for models with this feature)

Water ﬂow is adjusted by regulating the nozzle (6).

• Adjusting the detergent To deliver detergent at the correct

pressure, set the nozzle (6) on “ ” or ﬁt the detergent kit

(9) (where available) as shown.

USE OF THE APPLIANCE (Fig. D)

Controls

Starter device (19)

Set the starter switch on (ON/I) to:

a. Start the motor (In models without TSS device);

b. Set the motor ready to start (In models with TSS device).

If there is a pilot light on the starter device, it should light up.

Set the starter device switch on (OFF/0) to stop the appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SW21 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info