Bedienungsanleitung Stanley SXGP1300XFE (Seite 10 von 230) (Alle Sprachen)

720387

Zoom out

Zoom in

Vorherige Seite

1/230

Nächste Seite

10 11

(Translation of the original instructions)

6.3 Filling the appliance

Before fitting the delivery hose, completely fill the pump body (A4) and

the suction hose with water through the delivery fitting (A2). The pump

can also be filled through the filler cap (A2 b), if present (fig. 8).

Bubbles form during filling of the pump body (A4) and must be

discharged by tilting the appliance slightly in various directions.

Fill again and repeat this procedure until the water level is just below

the filling hole.

If the appliance has an integral pre-filter, more water must be added

through the cap of the pre-filter (A1 b). Open the cap, fill with water to

the rim and screw the cap back on by hand (fig. 8).

6.4 Fitting the delivery hose

The delivery pipe fitting is on the top of the appliance (A2). The hose

should be connected to a hose or pipe with the largest possible

diameter (at least 19 mm, ¾”). Smaller diameters drastically reduce

the appliance's flow rate. To ensure an airtight connection, use Teflon

tape (12 - 15 layers) (fig. 9).

6.5 Safety Measures

The user must prevent damage arising from the flooding of premises

or other causes in the event of a failure of the appliance or external

components by adopting suitable measures (e.g. installation of an

anti-flooding protection circuit, alarm system, backup pump, collection

tank or similar features), which must be connected to a separate,

fail-safe electrical circuit. The safety measures must be suited to the

specific conditions of use and must be able to reduce and/or prevent

the damage caused by water leaks.

The user must also install a spray guard to prevent water leaks or

splashes due to a pump failure from causing damage. A backup pump

or a floor drain must be installed to ensure that any water from leaks

is promptly removed. Otherwise, an alarm system can be installed

to trigger an alarm and/or an emergency shut-down of the appliance

and water supply in the event of a water leak, before damage to the

equipment or property can occur.

We also recommend raising all equipment in appliance installation

rooms about 5-10 cm above the floor so that any water leaks will

not cause immediate damage. The manufacturer accepts no liability

for damage caused by failure to comply with this recommendation.

Warning - danger! Dry operation

If the appliance runs for more than 5 minutes with the water suction point

closed, it may be damaged due to overheating. Switch off the appliance when

the normal water flow is obstructed.

Dry operation will damage the appliance beyond repair, so never allow

it to run dry for more than 10 seconds.

7 ADJUSTMENTS

7.1 Preliminary adjustments

Our appliances are preset in the factory and users must not modify

these settings.

8 START-UP

Warning - danger!

All installation and assembly operations must be performed with the appliance

disconnected from the mains power supply (g. 3).

8.1 Start-up

Once all the pipes have been connected and the pump body (A4) is

full of water, the plug (A12) can be connected and the ON/OFF switch

(A5) turned to ON. During the priming phase, the delivery pipe must

be open to allow the air in the system to escape and to enable the

water pressure to build up. If the suction hose is not completely full

of water, it may take the appliance up to 7 minutes to become fully

operational. If the water has not pressurised after the maximum

priming time stated, switch the appliance off and proceed as described

in the troubleshooting plan (chapter 11).

8.2 Technical information

The appliance's stated ow rate values are maximum values, which

are reduced if external components (e.g. delivery hose, elbows,

pre-lter, etc.) are used. This should be borne in mind when choosing

the appliance. The actual ow rate for specic installation conditions is

stated in the ow rate graph (g. 11).

9 MAINTENANCE

Warning - danger!

Before any maintenance procedure and/or during troubleshooting, disconnect

the power cable (A8) from the socket.

9.1 Cleaning the filters

Clean the pre-lter (if installed, A1 b) regularly with clean water

and/or inspect it to ensure that it is not fouled (g. 10). Sluice the lter

compartment with clean water.

10 STORAGE

Warning - danger!

Before any maintenance procedure and/or during troubleshooting, disconnect

the power cable (A8) from the socket.

It is essential to protect the appliance from frost, and in case of

temperatures of +5°C or below it must be uninstalled and stored

in a dry place, protected from frost. After disconnecting the suction

and delivery hoses, tilt the appliance to drain out all the water in the

pump body (A4) through the suction tting (A1). To empty the pump

body (A4) turn the appliance upside down to drain the water from the

delivery tting (A2).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SXGP1300XFE Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info