Bedienungsanleitung Stanley SXH1800 (Seite 4 von 8) (Englisch)

720680

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

ENGLISH

(Original instructions)

h. Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body leaves it unstable

and may lead to loss of control.

Before drilling into walls, ﬂoors or ceilings check for the

location of wiring and pipes.

Avoid touching the tip of a drill bit just after drilling, as it

may be hot.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source before

making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in

accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions and

the work to be performed. Use of the power tool for

operations different from those intended could result in a

hazardous situation.

5. Service

a. Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is

maintained.

Additional Safety Instructions for Heat Guns

1) A ﬁre may result if the appliance is not used with care,

therefore

- Do not apply to the same place for long time

- Do not sue in presence of an explosive atmosphere

- Be aware that heat may be conducted to combustible

materials that are out of sight

- Place the appliance on site after use and allow it to

cool down before storage

- Do not leave the appliance unattended when it

is switched on.

• Always switch off before putting tool down.

• Extreme care should be taken when stripping paint,

the peelings, residue and vapors of paint may contain

lead, which is poisonous. Once deposited on surfaces,

hand to mouth contact can result in the ingestion of lead.

Exposures to even low levels of lead can caused

irreversible brain and nervous system damage; young

and unborn children are particularly vulnerable. Do not

smoke, eat or drink in a work area that could or may be

contaminated by lead. Lead based paints should only

be removed by a professional and should not be

removed using a heat gun.

• When removing paints you should ensure that your

work area is enclosed. It is advisable to wear a dust

mask.

• Do not burn the paint. Keep the nozzle at least 25mm

(1”) from the surface as this keeps the temperature

below the required 450°C. If you are scraping from a

vertical position then you should scrape downwards to

prevent the paint from falling back into the heat gun and

burning. Dispose of all paint debris safely and ensure

that the work area is thoroughly cleaned after completing

the job.

• Do not use in a damp atmosphere or where

ﬂammable gases may be present or use near

combustible materials. Spaces behind boards, ceilings

and ﬂoors and wall cavities in timber frame constructed

houses can contain ﬂammable materials. Check before

using the heat gun.

• Allow the tool to cool fully before storing.

• Ensure adequate ventilation when using heat guns as

toxic fumes may be produced.

• Do not use as a hairdryer! The air temperature is far

higher than a hairdryer.

• Do not obstruct either the air intake or nozzle outlet as

this may cause excessive heat build up resulting in

damage to the tool.

• Do not direct the hot air blast at other people.

• Do not touch the metal nozzle as it becomes very hot

during use and remains hot for up to 30 minutes after

use. Do not look down the nozzle while the unit is

working because of the high temperatures being

produced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SXH1800 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info