Bedienungsanleitung Stanley SXPW25DTS (Seite 12 von 280) (Alle Sprachen)

720639

Zoom out

Zoom in

Vorherige Seite

1/280

Nächste Seite

(Original instructions)

GENERAL INFORMATION FIG.1/PAGE 3

4.1 Use of the manual

The manual forms an integral part of the appliance and should be

kept for future reference. Please read it carefully before installing/

using the unit. If the appliance is sold, the seller must pass on this

manual to the new owner along with the appliance.

4.2 Delivery

The appliance is delivered partially assembled in a cardboard box.

The supply package is illustrated in fig.1.

4.2.1 Documentation supplied with the appliance

A1 Use and maintenance manual

A2 Safety instructions

A3 Declaration of conformity

A4 Warranty regulations

4.3 Disposing of packaging

The packaging materials are not environmental pollutants but must

still be recycled or disposed of in compliance with the relevant

legislation in the country of use.

TECHNICAL INFORMATION FIG.1/PAGE 3

5.1 Envisaged use

This appliance has been designed for individual use for the cleaning

of vehicles, machines, boats, masonry, etc., to remove stubborn dirt

using clean water and biodegradable chemical detergents.

Vehicle engines may be washed only if the dirty water is disposed of

as per regulations in force.

- Intake water temperature: see data plate on the appliance.

- Intake water pressure: min. 0.1 MPa - max. 1 MPa.

- Operating ambient temperature: above 0°C.

The appliance is compliant with the IEC 60335-1 and IEC 60335-2-79

standards.

5.2 Operator

The symbol illustrated in fig. 1 identifies the appliance’s intended

operator (professional or non-professional).

5.3 Main components

B2 Lance

B3 Gun with safety catch

B4 Electric cable with plug (on models with this feature)

B5 High pressure hose

B6 Detergent tank (on models with this feature)

B7 Oil cap (on models with this feature)

E Nozzle

F Detergent regulator (on models with this feature)

G Pressure regulator (on models with this feature)

L Water filter

5.3.1 Accessories (if included in the supply package – see fig.1)

Nozzle cleaning tool

Rotating nozzle kit

Handle

Brush

Hose reel

Water suction kit

Pipe jet kit

Large surface cleaning brush kit

Adapter

C10

Screws

C11

Brackets

C12

Lever

C13

Detergent kit

C14

Wheels

C16

Pressure gauge

C17

Accessory adapter

C18

Twin Nozzle adapter

C19

5in1 Nozzle

5.4 Safety devices

- Starter device (H)

The starter device prevents accidental use of the appliance.

Warning

Do not tamper with or adjust the safety valve setting.

- Safety valve and/or pressure limiting valve.

The safety valve is also a pressure limiting valve. When the gun

trigger is released, the valve opens and the water recirculates

through the pump inlet or is discharged onto the ground.

- Thermostat valve (D1 where fitted) If the water temperature

exceeds the temperature set by the manufacturer, the thermostat

valve discharges the hot water and draws in an amount of cold

water equal to the amount of water discharged, until the correct

temperature is restored.

- Safety catch (D): prevents accidental spraying of water.

- Overload cutout: stops the appliance in case of overload.

INSTALLATION FIG.2/PAGE 4279

6.1 Assembly

Warning

All installation and assembly operations must be per-

formed with the appliance disconnected from the mains power

supply.

The assembly sequence is illustrated in fig.2.

6.2 Fitting the pressure release caps (on models with this feature)

To prevent oil leaks, the appliance is delivered with the oil intakes

sealed with red caps which must be replaced with the pressure

release caps supplied.

6.3 Fitting the rotating nozzle

(For models with this feature).

The rotating nozzle kit delivers greater washing power.

Use of the rotating nozzle may cause a reduction in pressure of

25% compared to the pressure obtained with the adjustable nozzle.

However, the rotating nozzle kit delivers greater washing power due

to the rotation of the water jet.

6.4 Electrical connection

Warning

Check that the electrical supply voltage and frequency

(V-Hz) correspond to those specified on the data plate (fig.2).

6.4.1 Use of extension cables

Use cables and plugs with "IPX5" protection level.

The cross-section of the extension cable should be pro-

portionate to its length; the longer it is, the greater its

cross-section should be. See table 1.

6.5 Water supply connection

Only clean or filtered water should be supplied to the appli-

ance. The flow rate of the water inlet tap should be equal to

the pump flow rate.

Place the appliance as close to the water supply system as possible.

6.5.1 Connection points

Water outlet (OUTLET)

Water inlet with filter (INLET)

6.5.2 Connection to the mains water supply

The appliance may only be connected directly to the

mains drinking water supply if the supply hose is fitted

with a backflow preventer valve as per current regulations

in force. Make sure that the hose is at least Ø 13 mm, that

it is reinforced and that it is not more than 25 m long.

6.5.3 Suction of water from open containers

1) Screw the inlet hose with filter to the water INLET and

insert it down to the bottom of the container.

2) Vent the air from the appliance:

a) Unscrew the lance.

b) Start the appliance and keep the gun open until there

are no air bubbles in the water flowing out.

3) Switch the appliance off and screw the lance back on.

N.B.: the maximum suction height is 0.5 m. The suction

hose should be filled before use.

ADJUSTMENTS FIG.3/PAGE 5

7.1 Adjusting the spray nozzle (for models with this feature)

Water flow is adjusted by regulating the nozzle (E).

Stanley SXPW25DTS Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info