720635

Stanley SXUP1000XWE Seite 10

10
Zoom out
Zoom in
Vorherige Seite
1/226
Nächste Seite
10 11
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
5.3 Main components (fig. 1)
A1 Suction strainer
A2 Threaded delivery fitting
A4 Pump body
A5 Rope eye-ring
A8 Power cable
A12 Plug
6 INSTALLATION
Warning - danger!
All installation and assembly operations must be performed with the appliance
disconnected from the mains power supply (fig. 3).
Warning - danger!
Before use, always perform a visual check on the appliance, and especially
the plug (A12) and power cable (A8), for damage. A damaged appliance must
not be used; in the event of damage, have the appliance inspected by the
Service Centre or an authorised electrician.
Warning - danger!
If the power cable (A8) is cut, the warranty becomes null and void and a
replacement genuine power cable (A8) must be installed during the repair,
at the customer's expense (even in case of repair under warranty). If it is
necessary to extend the power cable (A8), only use an extension with gauge
at least equal to that of the original power cable (A8). Never lift the appliance
or remove the plug (A12) from the socket by means of the power cable (A8).
6.1 Fitting the delivery hose
Connect a hose having inside diameter of at least 25 mm (1“), with
threaded fitting, to the delivery fitting (A2). A hose having diameter 32
mm (1-1/4‘‘) is preferable. Smaller hose diameters drastically reduce
the appliance's flow rate. To ensure an airtight connection, use Teflon
tape (12 - 15 layers) (fig. 4).
The use of a delivery hose with foot check valve is highly
recommended, in order to prevent the flowback of water when the
appliance is switched off.
Installing a quick shut-off valve to disconnect the hose in a suitable
point simplifies cleaning and maintenance.
6.2 Bleeding the appliance
The appliance is bled automatically provided it is immersed in
the liquid to sufficient depth.
Once the appliance has been started, make sure that the
delivery hose is open (not shut by a tap, for example) to allow
the residual air to escape.
6.3 Notes on the place of installation
The appliance is designed to be installed in a well at least 10 cm in
diameter, with an immersion depth of up to 16 m (fig. 5).
Before installing the appliance, a recovery rope must be fitted to the
eye-ring (A5) to allow it to be lowered into place/recovered easily
(fig.6).
If possible, the appliance should be suspended in the pumped liquid,
far enough off the bottom to prevent it from sucking in solids of
inappropriate size which may foul the suction strainer (A1) or jam
the impeller (fig. 6).
The appliance is cooled by the water it transports and the water in
which it is immersed. Make sure that the appliance is completely
immersed in the pumped liquid to ensure that it is cooled.
6.4 Safety Measures
Since the appliance does not have an ON/OFF switch, it should be
connected to a socket controlled by a supplementary ON/OFF switch.
Throughout all installation and use procedures, please bear in mind
that water leaks may cause damage.
Warning - danger! Dry operation
If the appliance runs for more than 5 minutes with the water suction
point closed, it may be damaged due to overheating. Switch off the
appliance when the normal water flow is obstructed.
Dry operation will damage the appliance beyond repair, so never allow
it to run dry for more than 10 seconds.
7 ADJUSTMENTS
7.1 Preliminary adjustments
Once the delivery hose has been connected, the appliance
is ready for use. Bear in mind that if a socket with ON/OFF
switch is not used, the appliance starts as soon as the plug
(A12) is connected.
8 START-UP
Warning - danger!
All installation and assembly operations must be performed with the appliance
disconnected from the mains power supply (g. 3).
8.1 Start-up
After connecting the appliance as described in point 6 and after
implementing all safety instructions, the plug (A12) can be connected.
8.2 Priming the appliance
The appliance sucks in water through the suction strainer (A1) in its
base and conveys it along the hose connected to the delivery tting
(A2).
Make sure that the appliance is continuously immersed in water when
in operation, to ensure that it does not run dry. When the user outlets
are shut, switch off the appliance using the ON/OFF switch or by
disconnecting the plug (A12).
8.3 Technical information
The appliance's stated ow rate values are maximum values, which
are reduced if the recommended head is exceeded and external
components (e.g. delivery hose, elbows, restrictors, etc.) are used.
This should be borne in mind when choosing the pump. The actual
ow rate for specic installation conditions is stated in the ow rate
graph (g. 7).
… 10 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stanley SXUP1000XWE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info