Bedienungsanleitung Stanley TLM220i - 77.116 (Seite 15 von 22) (Englisch)

622316

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Functions

Stanley TLM 220i 773938a en

FIN

RUS

EST

required stake out distance in the summary line between the stake out

point (first a and then b) and the instrument (rear reference).

If the Stanley TLM is then moved slowly along the stake out line the

displayed distance decreases. The instrument starts to beep at a distance

of 0.1m from the next stake out point.

The arrows in the display indicate in which direction the Stanley

TLM needs to be moved in order to achieve the defined distance (either a

or b). As soon as the staking out point is reached, the symbol appears

in the display.

The function can be stopped at any time by pressing the button.

Triangular area

The area of a triangle can be calculated by the measurement of three sides.

See drawing {N}.

Press the key once - the triangle symbol appears in the display.

Press the key and measure the first side of the triangle .

Press the key and measure the second side of the triangle .

Press the key and measure the third side of the triangle .

The result is shown in the summary row.

Press and hold the key to display additional information about the

measurement, such as the angle included by the first two measu-

rements and the perimeter of the triangle.

Indirect measurement

The instrument can calculate distances using Pythagoras’ theorem.

This procedure is helpful, if the distance to measure can not be reached

directly.

)

Make sure you adhere to the prescribed sequence of measu-

rement:

• All target points must be in a horizontal or vertical plane.

• The best results are achieved when the instrument is rotated about a

fixed point (e.g. with the positioning bracket fully folded out and the

instrument placed on a wall) or the Stanley TLM is mounted on a

tripod.

• The minimum/maximum function can be used - see explanation in

"Measuring -> Minimum/maximum measurement". The minimum value

must be used for measurements at right angles to the target; the

maximum distance for all other measurements.

Indirect measurement - determining a distance using 2

auxilliary measurements

See figure {P}

e.g. for measuring building heights or widths. It is helpful to use a tripod

when measuring heights that require the measurement of two or three

measurements.

Press this button once, the display shows . The laser is switched

on.

Aim at the upper point (1) and trigger the measurement . After

the first measurement the value is adopted. Keep the instrument as hori-

zontal as possible.

Press and hold down this button to trigger continuous measurement

, sweep the laser back and forth and up and down over the ideal target

point.

Press to stop continuous measurement (2). The result is displayed in

the summary line, the partial results in the secondary line.

Press and hold the key to display additional information about the

measurement of the angles of the triangle and .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley TLM220i - 77.116 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stanley TLM220i - 77.116

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info