Bedienungsanleitung StarTrac 7160 Series - Spinner PRO plus (Seite 24 von 28) (Englisch)

619005

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

| SPINNER PRO+ MANUFACTURED by STAR TRAC OWNER’S MANUAL

Inspection / Adjustment

Inspect major moving parts that require constant proper torque. Loose or misadjusted parts can result in personal injury or damage to the

bike. Check the following parts for security and/or proper torque.

Inspect all major moving parts that require constant proper torque. Loose or misadjusted parts can result in personal injury or

damage to the bike. Check the following parts for security and/or proper torque.

Pedals

Verify that the pedals are re-torqued after the first 10 hours of use and every 100 hours of operation, thereafter. Use a torque wrench

if components are loose.

NOTE: The pedal to the crank arm bolt torque is: 33-37 lb-ft.

IMPORTANT: If your facility allows members to interchange pedals, it is critical that the pedals are checked after each class to prevent

damage, which may lead to injuries if ignored.

Weekly Maintenance

Weekly maintenance should focus on the overall performance of the Spinner

indoor cycling bike. During these inspections, look for

vibration and possible loose assemblies.

Have an experienced rider ride each bike to identify and help diagnose any vibration, noises, and any "unusual" feeling from the drive

chain. Either faulty flywheel alignment or a loose chain can cause vibration.

 Check for proper flywheel alignment. Torque flywheel nuts as necessary.

 Remove chain guard and check for loose chain. Adjust chain as necessary.

Inspect each bike for loose assemblies, parts, bolts and nuts. Give particular attention to the following:

 Tighten all frame base hardware.

 Tighten all pop-pin handles.

 Tighten seat hardware.

 Tighten pedal toe clip / toe straps.

 Inspect and tighten tension knob assembly.

Monthly Maintenance

The monthly maintenance check should be a comprehensive inspection of the overall frame and main assembly components of the

Spinner indoor cycling bike in addition to the Weekly Maintenance.

Inspection and Adjustment

Inspect the frame and main assembly components for rust or corrosion. Tilt the bike or place in an upside down position to locate areas

where rust and corrosion may develop. Use a small, wire brush to remove rust build-up in small crevasses, such as leveling feet, pop pin

handles and other bolt assemblies. Give particular attention to the following areas:

 Leveling feet

 Pop pin handles

Inspect all wear items for adjustments or possible part replacement. Give particular attention to the following:

 Inspect brake pad for wear. Excessive wear, such as glazing or leather separation, indicates replacement is required.

 Inspect seat pad for wear. Rips, tears or excessive movement indicates replacement is required.

 Inspect pedals for play. Excessive movement of pedals indicates replacement is required.

 Tighten seat hardware.

 Tighten pedal toe clip / toe straps.

 Inspect and tighten tension knob assembly.

 Leveling feet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

StarTrac 7160 Series - Spinner PRO plus Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info