Bedienungsanleitung StarTrac IP-L3005 (Seite 11 von 20) (Englisch)

618991

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

INSTALLATION INSTRUCTIONS

• 5mm Hex Key Socket…………………………………...

• 6mm Hex Key Socket……………………………………

• 13mm Box / Open-End Wrench ……………….....

• 13mm Socket……………………………………………

• Torque Wrench…………………………………………

REQUIRED TOOLS:

GENERAL NOTES:

• Unless otherwise noted Loctite 242/243 or equivalent thread locker must be used on all threaded fasteners. (Do not use

thread locker when a Nyloc nut is used.)

• All Star Trac Strength equipment MUST be secured to the floor using either 10mm or 3/8in. (grade 5 minimum) bolts.

• This Installation Instructions Manual must be used in conjunction with the equipment’s Owner’s Manual. The Owner s

manual describes equipment setup and instructs members on how to use it correctly and safely.

• LEVERAGE requires at least two people to perform the installation.

THREAD LOCKER APPLICATION: Clean all threads and holes, apply no more than 3-4 drops per bolt.

Thru Holes Blind Holes

55.5 to 58 (41 to 43)1.7510mm

• Torque all hardware to values as specified above, unless noted otherwise.

• See hardware sheet of this manual for fastener sizing information; for reference only.

61 to 65 (45 to 48)1.2512mm

25.5 to 28.5 (19 to 21)1.258mm

10 to13.5 (8 to10)1.256mm

Torque, N-m (lbs-ft)Thread PitchBolt Size

Metric Steel Bolts Torque Specifications

Page 11

Should any component not be present or if you have any operational questions, please refer to your owner’s manual or on the

web @ www.startrac.com . Specifically refer to your Leverage serial number and model number labeled on your equipment.

PACKAGING REMOVAL:

Carefully remove all packaging materials that wrap the equipment. DO NOT USE A KNIFE OR BOX

CUTTER AS YOU MAY DAMAGE THE EQUIPMENT. At this time remove any sub-components from

the pallet and set aside for later assembly.

• Note: All torque values are in N-m unless otherwise stated.

WARNING: All taper roller bearings should ship from the factory packed with grease. It is the installers responsibility to

verify that ALL taper roller bearings are fully packed with grease before assembly of the LEVERAGE product begins. If

any bearing needs grease added use a general purpose Lithium Grade 2 grease. Fully pack the roller bearing with

grease by forcing the grease under the bearing cage between the rollers from the large end of the roller until it oozes

thru the small end.

Failure to correctly lubricate bearings and maintain proper lubrication may result in damage that could cause bearing to

fail during operation, creating a risk of serious bodily harm.

PACKAGING REMOVAL:

Carefully remove all packaging materials that wrap the equipment. DO NOT USE A KNIFE OR BOX

CUTTER AS YOU MAY DAMAGE THE EQUIPMENT. At this time remove any sub-components from

the pallet and set aside for later assembly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

StarTrac IP-L3005 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info