Bedienungsanleitung StarTrac S-TRx Treadmill (Seite 42 von 52) (Englisch)

619139

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

1. Turn the treadmill on. Increase treadmill speed to 3.0 mph (5.0 kph).

2. Adjust tracking by adjusting the tailroller Allen screws (located at the back sides of the tailroller) with a 1/4" Allen

wrench in 1/4-turn increments.

If the running belt is tracking to the left, adjust the running belt to track to the right. Tighten the left tailroller

Allen screw by turning clockwise, or loosen the right tailroller bolt by turning counter-clockwise.

If the running belt is tracking to the right, adjust the running belt to track to the left. Tighten the right tailroller

Allen screw by turning clockwise or loosen the left tailroller bolt by turning counter-clockwise.

3. After the running belt appears to be tracking properly, increase the treadmill speed to 10.0 mph (16.0 kph) and

verify that the belt stays centered.

Slipping-Running Belt: Remove the motor shroud and operate the treadmill slowly at 1 to 2 mph (2 to 3 kph). While

observing the headroller, walk on the belt and try to slow it down by gently applying pressure with your feet while holding

the handrails. If only the running belt, and not the headroller, slows down, tighten the running belt by turning both the right

and left tailroller adjustment bolts clockwise 1/4-turn. Repeat this adjustment until the running belt no longer slips,

ensuring that you turn both tailroller bolts an equal number of turns. Re-install the motor shroud. If the headroller and the

running belt both slow down, tighten the drive belt as described under “Slipping-Drive Belt”, below.

Thumping: Turn the treadmill off. Turn the right and left tailroller adjustment bolts counter-clockwise with the M6 Allen

wrench until the running belt is loose. Note the number of times each bolt is turned. Remove excess accumulated running

deck wax from the tailroller with a credit card, a putty knife, or other flexible plastic implement. Tighten the running belt by

turning the adjustment bolts clockwise the same number of turns as they were loosened. Turn the treadmill on and check

for sideward movement and/or slipping of the running belt. Tighten the tailroller adjustment bolts further, if necessary, in

1/4-turn increments.

REWAX BELT

Periodic running belt rewaxing virtually eliminates belt down time, and maximizes the life of the belt. Whenever the present

distance is 2000 miles (or 3000 km) more than the LAST DECK (last deck service), the start-up display will scroll REWAX

BELT. This is a reminder to have your maintenance or service provider perform the 5-minute belt rewaxing procedure at

your convenience. (Immediate service is not required). Wax is included in the treadmill.

TOOLS & MATERIALS

Bottle of Wax Powder (1)

Clean Towel (1)

Paint Stick or Ruler (1)

Diluted All-purpose Cleaner (409), or Bristle Brush

PROCEDURE

Apply wax powder while belt & deck are still warm

(5 minutes minimum use) for optimum benefit.

1. CAUTION: turn treadmill power off and unplug the power cord before rewaxing the belt.

2. CLEAN DECK & BELT:

A. Using the paint stick or ruler, slide a towel under the middle of the belt from one side of the frame to the other.

B. Hold the edges of the towel; pull to the tailroller; pull to the headroller; then pull the belt down to wipe the

remaining belt. TIP: Fold the dirty towel and shake into trash.

3. LIFT BELT: Lift the left side (facing display) of the belt, about 12 inches down from the motor shroud (see figure).

Hold the belt up to elevate the belt from the deck.

4. SPREAD WAX: Flip the nozzle on the cap of the wax bottle. Point the nozzle at the deck. Be sure that the bottle is

tilted at a downward angle. Squeeze the wax bottle twice between the running belt and the deck. TIP: Gently shake

the bottle between each squeeze.

5. Repeat steps 3 and 4, about 18 inches from the end of the deck.

6. Repeat steps 3 through 5, on the right side of the belt/deck.

7. WALK: Plug in the treadmill. Turn the treadmill ON/OFF switch to the ON position. Start the treadmill at 1 mph

and walk on all sections of the belt and deck for 1 minute to ensure the wax has been evenly distributed and

worked-in properly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

StarTrac S-TRx Treadmill Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info