Bedienungsanleitung Steba Litho (Seite 6 von 13) (Deutsch, Englisch, Holländisch, Französisch)

535773

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Generally

This appliance is for private use only and must not be used commercially. Please read

the instruction manual carefully and keep it at a safe place. When the appliance is

given to another person the instruction manual should be passed to that person, too.

Only use the appliance as described in the instruction manual and pay attention to

the safety information. No liability for damages or accidents will be accepted, which

are caused by not paying attention to the instruction manual.

Your product

Other than the heater you have chosen the package includes (picture 1):

- N° 2 plastic brackets for wall mounting;

- N° 4 rawplugs 6x25mm;

- N° 4 3,5x55mm cross head screws to x wall brackets;

- N° 1 drill pattern for wall mounting.

Refer to your dealer is something is broken or missing.

Safety information:

Connect and operate the appliance only in accordance with the specifications on ∙

the rating label.

Do not use if the power cord is damaged. This must be checked before each use. ∙

∙ This appliance is not intended for use by persons (including children)

with reduced physical, sensory, or mental capacities, or lack of experience

and knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety

Children should be supervised to ensure that they do not play with the appliance. ∙

The appliance is not intended to be operated by means of an external timer or ∙

separate remote control system.

After each use or in the case of a malfunction the plug must be pulled out of the ∙

socket.

Never pull at the power cord. Do not chafe it over sharp edges or squeeze it. ∙

CAUTION ∙ — Some parts of this product can become very hot and cause

burns. Particular attention has to be given where children and vulnerable

people are present.

Make sure that your supply rating corresponds to what specified on the rat- ∙

ing plate: 230V~, 50Hz.

The product has a double IP protection level against water: IPX1 when ∙

portable and IPX4 when wall mounted (picture 2). Respect your country

regulations about the use of the product in different environments.

Don't leave your home while the appliance is in function: ensure in this case that ∙

the switch is in OFF (0) position and the thermostat is in minimum position ().

During function, place the heater in a safe position: ∙

- at least 1m far from inflammable objects or furnitures;

- leaving not less than 1m of free space in front of the heater;

- not located immediately below a socket-outlet.

Do not leave animals or children touch or play with the appliance. Pay attention! ∙

The air outlet grille gets hot during operation (more than 90°C)

∙ WARNING: In order to avoid overheating, do not cover the heater.

Do not hang anything on the heater and do not cover it while it’s wor-

king. This is clearly written on the cover of the product or shown by the

symbol

Do not use the heater in rooms with explosive gas or while using inflammable ∙

solvents or varnish or glues.

If the cordset is damaged and you have to change it, do not do the job yourselves! ∙

Take the product to an after sales authorised repair centre or to a person with simi-

lar skill and knowledge, in order to avoid any risk of danger.

When portable, do not use this heater close to showers, baths, swimming pools. ∙

The appliance must be positioned so that the plug is always accessible. ∙

Do not mount the product on walls made of synthetic material. ∙

Wall mounting

Only fix the heater in vertical position with the air outlet grid downword; ∙

This heater is fitted with a double electrical insulation circuit (class II) and therefore ∙

does not require an earth connection.

When wall mounted, the heater is water resistant to IPX4. It can therefore be used ∙

in bathrooms or other areas subject to humidity as long as it is not installed within

the perimeter of bath tubs or showers. This means that it cannot be installed in the

areas marked as VOLUME 1 in figure 1.

It must never be possible for people in the bath tub or shower to reach the adjust- ∙

ment knobs.

This heater must be correctly installed in compliance with the regulations in force in ∙

the country of installation.

IMPORTANT FOR FRANCE: ∙

If the product is to be wall mounted the electrical connection to the power supply

must be done by cutting off the plug supplied and using a suitable terminal as per

the diagram shown below:

 WARNING: In order to avoid overheating, do not cover the heater. Do not hang anything on

the heater and do not cover it while it’s working. This is clearly written on the cover of the product

or shown by the symbol

 Do not use the heater in rooms with explosive gas or while using inflammable solvents or varnish

or glues.

 If the cordset is damaged and you have to change it, do not do the job yourselves! Take the

product to an after sales authorised repair centre or to a person with similar skill and knowledge,

in order to avoid any risk of danger.

 When portable, do not use this heater close to showers, baths, swimming pools.

 The appliance must be positioned so that the plug is always accessible.

 Do not mount the product on walls made of synthetic material.

3. Wall mounting

 Only fix the heater in vertical position with the air outlet grid downword;

 This heater is fitted with a double electrical insulation circuit (class II) and therefore does not

require an earth connection.

 When wall mounted, the heater is water resistant to IPX4. It can therefore be used in bathrooms

or other areas subject to humidity as long as it is not installed within the perimeter of bath tubs or

showers. This means that it cannot be installed in the areas marked as VOLUME 1 in figure 1.

 It must never be possible for people in the bath tub or shower to reach the adjustment knobs.

 This heater must be correctly installed in compliance with the regulations in force in the country of

installation.

 IMPORTANT FOR FRANCE:

If the product is to be wall mounted the electrical connection to the power supply must be done

by cutting off the plug supplied and using a suitable terminal as per the diagram shown below:

In wet spaces like bathrooms or kitchens, the connection terminal must be installed at least 25

cm above the floor. The electrical connection to the power supply must also be fitted with a two-

pole switch with a minimum gap between the contacts that allows complete disconnection

according to excess voltage III category conditions.

 Mount the heater on the wall making sure to observe the minimum distances from the ceiling,

floor and other walls, as shown in picture 4;

 To proceed with the installation:

 Drill four 6 mm diameter holes in the wall, as shown in picture 5. A drill pattern is provided to

help you marking the correct position of the holes;

 Insert the four wall plugs supplied with the product;

 Fix the upper and the lower brackets as shown in picture 6;

 Hang the product to the upper bracket and then hook it up to the lower bracket untill you ear a

“click” as shown in picture 7.

4. Portable use

 If you want to use the fan heater as portable you have to extract the foot placed on the back of

the appliance as shown in picture 8. Just pull it until you ear a “click” and check that the foot is

firmly locked in its extracetd position.

5. Using the fan heater

 The heater is fitted with a switch and an ambient thermostat as shown in picture 9.

 The switch is used to control heater’s functioning selecting the off condition, cold air ventilation,

warm air (1000W) or hot air (1800W).

 The heater is also equiped with an alarm light (picture 10) that switches on in case of

overheting/malfunctioning. It is not a functioning light and, consequentely, it will not switch on

during normal functioning.

 Do not put anything on the heater to avoid any overheating/malfunctioning both in portable use

(picture 11) or fixed installation (picture 4).

Using the thermostat



In a room with a temperature exceeding 30°C, the thermostat does not turn on the fan heater

even if it is at maximum.

 Vice-versa, in a room with a very low temperature (below 5°C), it is normal that the thermostat

keeps the heater constantly on, even if it is at minimum.

 To optimise use of the thermostat, proceed as follows:

- turn the thermostat knob to maximum and wait until a comfortable temperature is reached;

- then turn the thermostat knob anti-clockwise until you hear a “click” and the heater turns off;

- turn the thermostat knob clockwise just a little;

- in this position, the thermostat will maintain the selected ambient temperature.

6. Filter

 This product is fitted with a filter to protect the heating element from dust and dirt.

 The filter is removable to be easily cleaned with water.

 To remove the filter just unlock the tab by pressing on it and pull towards you as shown in picture

12.

 To keep the heater in perfect condition, clean the filter once every six months REMEMBERING

TO PUT IT BACK AGAIN AFTERWARDS.

7. Troubleshooting

 In the event of overheating, the safety device on the appliance automatically disabled the heating

elements and motor. As a result, the heater stops working and the alarm light switches on. In this

case:

- Turn off the fan heater and allow it to cool down for about 15/20 minutes.

- Make sure the dust filter is not totally obstructed and clean if necessary. Remember to put it

back again afterwards.

- Eliminate any other possible reasons for overheating (e.g.: obstructions in front of the air

inlet/outlet grilles, build-ups of dirt).

- Turn on the fan heater again and check it works correctly.

8. Maintenance

 This product does not require any special maintenance.

 Clean the product with a dry cloth once every 6 months.

 If the product requires repairing, contact an authorised technical service centre.

 When replacing the power cable, use a 2x1,00mm

H05VV-F HAR type. This operation must be

performed by qualified personnel and never by the end user in order to avoid damaging the

appliance and jeopardising personal safety.

9. Legal notice

Environment and recycling

Please help us to protect the environment by disposing of the packaging in accordance with

the national

regulations for waste processing.

Recycling of obsolete appliances

Appliances with this label must not be disposed off with the general waste. They must be

collected separately and disposed off according to local regulations.

Net

Phase = brown

Neutral = blue

Product cable

In wet spaces like bathrooms or kitchens, the connection terminal must be installed ∙

at least 25 cm above the floor. The electrical connection to the power supply must

also be fitted with a two-pole switch with a minimum gap between the contacts

that allows complete disconnection according to excess voltage III category condi-

tions.

Mount the heater on the wall making sure to observe the minimum distances from ∙

the ceiling, floor and other walls, as shown in picture 4;

To proceed with the installation: ∙

Steba Litho Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info