Bedienungsanleitung Steel Cucine PARTY (Seite 72 von 220) (Deutsch, Englisch, Französisch, Italienisch)

651782

Zoom out

Zoom in

Vorherige Seite

1/220

Nächste Seite

Instructions for the installer

3.7 Gas connection

The appliance's setting conditions are stated on the plate on the back of the appliance.

Gas-powered devices for home use, which are not connected to a conduit for the evacuation of

combustion products, must not cause a concentration of carbon monoxide that could pose a health

risk to the persons exposed in relation to the time of exposure.

We recommend checking that the appliance is properly set up for the type of

gas distributed. The connection to the gas pipes must be made in a

workmanlike manner, in compliance with current standards that prescribe the

installation of a safety tap at the end of the pipe. The threaded ½" gas

connection pipe is located at the rear on the right hand side of the appliance.

We recommend checking that the appliance is properly set up for the type of

gas distributed. The connection to the gas pipes must be made in a

workmanlike manner, in compliance with current standards that prescribe the

installation of a safety tap at the end of the pipe. The Gas Connection is

male ½" BSP and is situated at the left hand, top rear of the appliance,

74mm from the side and 700mm from the floor (cookers) or 25mm from the

underside (cooktops). The appliance is factory set for Natural gas. The test

point pressure should be adjusted to 1.00kPa with the Wok and Semi-Rapid

burners operating at maximum on 120cm models and the Wok burner

operating at maximum on 90cm models.

For butane and propane, a pressure reducer conforming to standards regulations in force should

be prepared. The seals must conform to standards regulations in force.

Once the gas has been connected, check the seal of the unions with a soap and water solution.

For propane a pressure regulator set to provide a supply pressure of 2.75kPa conforming to

standards regulations in force should be fitted. The seals must conform to standards regulations in

force. Fit the test point assembly supplied with the appliance to the gas connection when installing

for use with Propane Gas. Once the gas has been connected, check the seal of the unions with a

soap and water solution.

It is possible to connect the gas in the following ways:

• using iron or copper rigid pipe as specified in AS5601 table 3.1;

• using a Plumbezy flexible hose, AGA approval number 6196, 10mm ID, class D and between

1-1.2m long in accordance with AG601 for a "high level connection". For cookers supplied with

a flexible hose the restraining chain fitted to the rear of the cooker must be fixed to the wall as

follows.

1. Supply fixing points on either side of the cooker (vertically in line with the chains attached)

at approxiametely 100mm above floor level.

2. Firmly secure the chains at these points.

3. Supply similar fixing points at approxiametely 700mm above floor level using open hooks.

4. Loop the chains over these hooks to prevent the cooker from accidentally tilting.

5. Removing the chains from the hooks enables the cooker to be pulled out for service. Ensure

that the chains prevent stress on the hose assembly while the cooker is in this position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steel Cucine PARTY Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info