Bedienungsanleitung Steinberg Sequel (Seite 81 von 97) (Englisch)

701005

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

Setting up your system

About this chapter

In this chapter, you will find information on the basic com-

puter setup (audio card and drivers, etc.) and on more ad-

vanced audio and MIDI system setups.

General notes on how to set up your

system

• RAM – There is a direct relation between the amount of

available RAM and the number of audio channels that you

can have running.

The amount of RAM specified above is the minimum requirement, but as

a general rule “the more the better” applies.

• Hard disk size – The size of the hard disk determines

how many minutes of audio you will be able to record.

Recording one minute of stereo CD quality audio requires 10 MB of hard

disk space. That is, eight stereo tracks in Sequel use up at least 80 MB

of disk space per recording minute.

• Hard disk speed – The speed of the hard drive also de-

termines the number of audio tracks you can run.

That is the quantity of information that the disk can read, usually expressed

as “sustained transfer rate”. Again, “the more the better” applies.

• Wheel mouse – We recommend that you use a wheel

mouse.

This will speed up value editing and scrolling considerably.

Defragmenting the hard disk

(Windows only)

If you plan to record audio on a hard disk where you have

already stored other files, now is the time to defragment it.

Use the Windows Defragmentation tool to optimize your

system’s performance.

MIDI requirements

If you intend to use the MIDI features of Sequel, you need

the following:

• A MIDI interface to connect external MIDI equipment to your

computer.

•A MIDI instrument.

• Any audio equipment required to listen to the sound from your

MIDI devices.

Installing a MIDI interface/synthesizer card

Installation instructions for a MIDI interface should be in-

cluded with the product. However, here’s an outline of the

necessary steps:

1. Install the interface (or MIDI synthesizer card) inside

your computer or connect it to a “port” (connector) on the

computer.

Which is right for you depends on which type of interface you have.

2. If the interface has a power supply and/or a power

switch, turn it on.

3. Install the driver for the interface, as described in the

documentation that comes with the interface.

You should also make sure to check the manufacturer’s web site for the

latest driver updates.

Audio hardware

Sequel will run with audio hardware that meets the follow-

ing specifications:

•Stereo.

•16 bit.

• Sampling rate: 44.1kHz.

• Windows – The audio hardware must be supplied with a spe-

cial ASIO driver, or a DirectX compatible driver, see below.

• Mac – The audio hardware must be supplied with Mac OS X

compatible drivers (CoreAudio or ASIO).

On the Steinberg web site, under “Support-DAW

Components”, you can find detailed information on

what to consider when setting up a computer system

dedicated to audio work.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinberg Sequel Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info