Bedienungsanleitung Steinel Dual US (Seite 12 von 43) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch, Schwedisch)

593155

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

- 22 - - 23 -

Technical Specifications

Dimensions (W x H x D): 120 x 120 x 68 mm DualTech

120 x 120 x 73 mm Single US

120 x 120 x 68 mm US 360

120 x 120 x 73 mm Dual US

Power supply: 230 – 240 V, 50 Hz / 60 Hz

Capacity, switching output 1: Relay, 230 V

(COM 1/COM 2) 2000 W max. resistive load (cos φ = 1)

1000 VA max. (cos φ = 0.5)

Electronic ballasts: Max. ON current 800 A/200 μs

(COM 1/COM 1 AP/COM 2/DIM) 30 x (1 x 18 W), 25 x (2 x 18 W)

25 x (1 x 36 W), 15 x (2 x 36 W)

20 x (1 x 58 W), 10 x (2 x 58 W)

Pay attention to specific ON currents of electronic ballasts!

A relay or contactor must be provided on line side for

higher switching capacities

Capacity, switching output 2: Presence

(COM 2 only) 230 W/230 V

1A max. (cos φ = 1) for HVAC (heating/ventilation/air-conditioning)

Detection ranges: US 360/DualTech SingleUS/Dual US

(Detection Tangential/presence (m): Ø 6 m max. (28 m

)

at 2.5 m / mounting Ø 2 m min. (12 m

)

height 2.5 m) Radial: Reach up to Ø 10 m 3 x 10 m / 3 x 20 m (30 / 60 m²) max.

3 x 2.5 m / 3 x 5 m (7.5 / 15 m²) min.

Light-level setting: 10 – 1000 lux, ∞ / daylight /

DIM 100 – 1000 lux control threshold

Switching output 1: 30 sec. – 30 min., pulse mode (approx. 2 sec.),

Time setting IQ mode (automatic adjustment to the usage profile)

Switching output 2: COM2 only, for HVAC

Time setting 0 sec. – 10 min. switch-ON delay

1 min. – 2 hrs. stay-ON time

Automatic room surveillance

DIM: 30 sec. – 30 min.,

Time setting IQ mode (automatic adjustment to the usage profile)

Control output: 1 – 10 V / 50 electronic ballasts max., 100 mA max.

Mounting height: 2.5 m – 3.5 m

(mounted to ceiling)

Point of installation: Indoors

Sensor technology:

DualTech PIR (Passive Infrared), single pyro, 11 detection levels,

520 switching zones. Ultrasonic 40 kHz

US 360 / Single US / DualTech Ultrasonic 40 kHz

IP rating: IP 20

Protection class: II

Temperature range: - 25 °C - +55 °C

DIP 4

In the ON-OFF setting, the light

can be switched ON and OFF

manually at any time (except in

pulse mode: no manual OFF).

In the ON setting, light can no

longer be switched OFF manual-

ly. The stay-ON time starts from

the beginning again each time

the button is pressed.

ON/ON-OFF button

DIP 1

Functions – Settings by DIP switch

Test mode has priority over all

other settings on the presence

detector and serves the purpose

of checking for proper working

order as well for testing the de-

tection zone. Irrespective of

ambient light level, the presence

detector activates the light to

stay ON for approx. 8 sec. in

response to movement in the

room. (blue LED flashes when

movement is detected).

All user-selected potentiometer

settings apply in normal mode.

The presence detector can also

be set by means of the blue LED

without any load connected.

Normal mode / Test mode (NORM / TEST)

DIP 2

The light automatically switches

ON and OFF in relation to light

level when someone is present.

Light can be switched ON and

OFF manually at any time. This

temporarily interrupts the auto-

matic switching function. Irre-

spective of the settings selected,

light stays ON for 4 hours after

manually pressing the button

twice or switches OFF after man-

ually pressing the button once.

Pressing the button before the

4 hours elapse returns the pres-

ence detectors to the normal

operating mode.

Semi-automatic mode (MAN) / fully automatic mode (AUTO)

Fully automatic mode: (AUTO)

Semi-automatic mode: (MAN)

The light now only switches

OFF automatically. Light is

switched ON manually.

Light must be requested using

the button and stays ON for the

time set at the potentiometer

(pressing twice switches ON for

4 hours).

DIP 3

Tells the sensor how to interpret

the incoming signal. Assigning

external buttons/switches allows

you to operate the detector as a

semi-automatic unit and over-

ride it manually at any time.

n Operation either by button or

switch

n Several buttons possible on

one control input

n Only use illuminated pushbut-

ton with neutral conductor

connected

nCable length between sensor

and switch < 50 m

Button/switch

COM 1 + COM 2

DIP 5

Provides a constant level of

brightness. Detector measures

the prevailing level of daylight

and activates sufficient artificial

light to achieve the required lev-

el of brightness. As daylight

changes, the switched-in artifi-

cial lighting component is ad-

justed accordingly. In addition to

the daylight component, artificial

light is also switched ON and OFF

in relation to whether or not per-

sons are present.

Constant light ON/OFF

DIM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel Dual US Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info