Bedienungsanleitung Steinel GL 80 C (Seite 20 von 155) (Alle Sprachen)

758083

Zoom out

Zoom in

Vorherige Seite

1/155

Nächste Seite

- 39 -- 38 -

This function only ever applies to the C types in combination with a Bluetooth

sensor-switched product.

Twilight setting (response threshold)

The chosen response thresholdcan be inﬁnitely varied from approx. 2 to

2000 lux.

– Control dial turned fully clockwise = daylight mode (depending on ambient

brightness)

– Control dial turned fully anti-clockwise = twilight operation (approx. 2 lux)

This function only ever applies to the C types in combination with a Bluetooth

sensor-switched product.

The control dial must be turned fully clockwise when adjusting the detection

zone and performing the walk test in daylight.

Night-light function

The night light provides illumination at approx. 10% of full light output. The light

only switches to maximum output (100%) in response to movement in the

detection zone (see Time setting). The light

then switches to the activated night light level.

Night light is ON when the level of light falls below the brightness threshold.

Night light is always ON when daylight mode is activated.

0min = soft light start / no night ON from twilight setting selected

10min = soft light start + night light for 10minutes

30min = soft light start + night light for 30minutes

= soft light start + night light all night long

This function only ever applies to the C types in combination with a Bluetooth

sensor-switched product.

What is soft light start?

The sensor-switched light features a soft light start function. This means that

when turned ON, the light is not switched directly to maximum output but con-

stantly builds up brightness to 100% within a short period of time. Brightness is

also gradually reduced when the light is switched OFF.

This function only ever applies to the C types in combination with a

Bluetooth sensor-switched product.

Manual override function (Fig.6.1)

If an optional mains switch is installed in the mains supply lead, the following

functions are available in addition to simply switching light ON and OFF:

1) Activate manual override:

Switch OFF and ON twice. The light is set to manual override for 4 hours. Then

it returns automatically to sensor mode.

2) Deactivate manual override:

Switch OFF and ON once. Light switches OFF or switches to sensor operation.

Important: Switching must take place within 0.2 to 1 second.

7. Maintenance / care

The product requires no maintenance.

The light can be cleaned with a damp cloth (without detergents) if dirty.

Important note: the control gear cannot be replaced.

8. Disposal

Electrical and electronic equipment, accessories and packaging must be

recycled in an environmentally compatible manner.

Do not dispose of electrical and electronic equipment as domestic

waste.

EU countries only:

Under the current European Directive on Waste Electrical and Electronic Equip-

ment and its implementation in national law, electrical and electronic equipment

no longer suitable for use must be collected separately and recycled in an

environmentally compatible manner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel GL 80 C Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info