Safety Notification
Caution! When using electric
power tools, observe the fol-
lowing basic safety precau-
tions to avoid electric shock
as well as the risk of injury
and fire. Read and observe
this information before using
the tool.
y
Fire may be caused if the
tool is not used with care.
y
Take ambient conditions
into account.
–
Do not expose power tools
to rain.
–
Do not use power tools
when they are damp or in
damp or wet surroundings.
–
Exercise care when using
the tool in the proximity of
combustible materials. Do
not direct the tools at one
and the same place for a
prolonged period.
–
Do not use in the pre-
sence of an explosive
atmosphere.
–
Heat may be conducted to
combustible materials that
are out of sight.
y
Protect yourself from
electric shock.
–
Avoid touching grounded
equipment, such as piping,
radiators, cookers, refrige-
rators.
y
Do not leave the appli-
ance unattended while in
operation.
y
Store your tools in a safe
place.
–
Place tool on its stand
after use and allow to cool
before storage.
–
Tools that are not in use
should be stored in a dry,
locked room and be out of
the reach of children.
y
Do not overload the tool.
–
Your work results and
safety will be enhanced if
you operate the tool within
the specified output range.
–
After using the tool for a
prolonged period at
600° C, you should reduce
the temperature before
switching it off. This will
prolong the service life of
the heating element.
y
Beware of toxic gases
and ignition hazards.
–
Toxic gases may occur
when working on plastics,
paints, varnishes or similar
materials. Beware of fire or
ignition hazards.
y
Do not misuse the power
cord.
–
Do not carry the tool by
the power cord and do not
use it to pull the plug from
the power socket outlet.
Protect the power cord
from heat, oil and sharp
edges.
y
Caution
–
For your own safety, use
only accessories and
attachments that are given
in the operating instruc-
tions or recommended or
specified by the tool
manufacturer. Using
attachments or accesso-
ries other than those
recommended in the
operating instructions or
catalogue may result in
personal injury.
y
Repairs only by qualified
electricians.
–
This power tool complies
with the relevant safety
regulations. Repairs
should only be performed
by a qualified electrician,
otherwise the user may
run the risk of accidents.
y
Failure to observe the
operating instructions
may turn the tool into a
source of danger.
y
Keep these safety notifi-
cations in a safe place.
Operation
Switch the tool on with
ON/OFF switch
.
Use temperature switch
to
preset the target temperatu-
re you require (25° C - 600°
C). The temperature setting
as well as the letter "A" to
show the setting mode will
appear on the LED segment
display. Once the tempera-
ture has been preset, the
tool will automatically dis-
play the actual temperature
after approx. 3 seconds.
Target and actual temperatu-
re is displayed in increments
of 10° C.
The air flow rate
may be
infinitely varied using the
airflow regulator.
The control system complies
with the latest standards on
mains pollution
(EN 61000-3-3 Flicker
standard, EN 61000-3-2
Harmonics standard).
The tool features an intelli-
gent temperature and
airflow control system that
always gives priority to tem-
perature setting (see graph).
Example: To attain the maxi-
mum temperature of 600° C
with speed set to max. air
flow rate, the electronics will
automatically reduce air flow
until 600° C is reached. The
airflow rate will then in-
crease again as soon as the
temperature is reduced.
Intelligent Motor and Temperature Monitoring
Intelligent Motor and Temperature Monitoring
Motor speed
(rpm)
Dyn. pressure
(hPa)
Outlet temperature
10 11
GB
