Bedienungsanleitung Steinel HL2020E (Seite 7 von 81) (Alle Sprachen)

593129

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

- 13 -

Keeping the button pressed will continue to increase or re-

duce the temperature in steps of 10 °C until the rocker but-

on is released or the minimum or maximum temperature is

set. The temperature setting is shown on the display for

seconds. On lowering or increasing the temperature, the

actual temperature is then displayed at the delivery nozzle.

he °C/°F symbol flashes during this period. As soon as the

selected temperature is reached, this symbol stops flashing

and is displayed all the time. Blower stage 1 delivers a tem-

erature of 80 °C. When the tool has been operating at high

temperatures on blower stage 2 or 3 it will take a short while

o cool to 80 °C after switching down to blower stage 1.

While the tool is cooling down, the LCD display (10) shows

he actual temperature at the nozzle outlet. After switching

off, the tool stays in the last setting that was selected. The

guard sleeve (3) detaches at a bayonet catch.

Changing the power cord (HL 2020 E only)

If the power cord is damaged, it can easily be changed

without opening the casing.

1. Important! Disconnect tool from power supply.

2. Undo screw and remove cover cap .

3. Release cable grip .

4. Undo mains terminals .

5. Pull out cord .

6. Insert new cord and secure in reverse order

(1. Firmly screw down mains terminals etc.).

Residual heat indicator

(HL 2020 E only)

The residual heat indicator serves as

a visual warning to prevent injury

from direct contact with the hot

nozzle outlet. The residual heat indi-

cator also works when the tool is

unplugged.

The indicator starts working after the

tool has been in use for 90 seconds

and keeps flashing until the tempera-

ture at the nozzle outlet has fallen

below 60 °C at room temperature.

The residual heat indicator does not

show if the tool has been in opera-

tion for less than 90 seconds. Re-

sponsibility always rests with the

user and care must be taken at all

times when handling hot air tools.

Keep these safety precautions

with the tool.

- 12 -

Technical specifications

HL 1620 S

HL 1920 E

HL 2020 E

Subject to technical modifications

Voltage

Output

Stage

Airflow rate (l/min.)

Temperature (°C)

Temperature setting

Temperature display

Residual heat indicator

Protection class

(without earth terminal)

Thermostat

Thermal cut-out

Emission sound

pressure level

Total vibration value

Weight

220-230 V, 50/60 Hz

2200 W

12 3

150 150-300 300-500

80 80-630

infinitely variable in 10 °C

steps by pushbutton

LCD indicator

Yes

≤ 70dB (A)

≤ 2.5 m/s

K = 0.08 m/s

0.880 kg

220-230 V, 50/60 Hz

2000 W

12 3

150 150-300 300-500

80 80-600

Infinitely variable in 9

increments by setting dial

–

Yes

≤ 70dB (A)

≤ 2.5 m/s

K = 0.08 m/s

0.840 kg

220-230 V, 50/60 Hz

1600 W

240 450

300 500

–

Yes

≤ 70dB (A)

≤ 2.5 m/s

K = 0.08 m/s

0.670 kg

Safety warnings

These hot air tools are doubly protected from overheating:

. A thermostat switches the heater off if too much of the

air outlet nozzle is obstructed (heat build-up). However,

he blower continues to run. A warning triangle on the

display tells you that the heater is switched off.

Once the air delivery nozzle is clear again, the heater au-

omatically switches back on again after a few moments.

The warning triangle then goes out. The thermostat may

lso respond after switching the hot air tool off, taking it

longer than usual to reach temperature at the air delivery

ozzle when it is switched on again. *

2. The thermal cut-out completely shuts down the tool if it is

overloaded.

* for HL 2020 E only

For your safety

Tool description - Operation

Please note: The distance from the object you are working

on depends on material and intended method of working.

Always try out the airflow and temperature on a test piece

first. Using the attachable accessory nozzles (see acces-

sories page on the cover) the flow of hot air can be con-

trolled with maximum precision. Take care when changing

hot nozzles! When using the hot air tool in the self-resting

position, make sure it is standing on a stable, non-slip and

clean surface.

HL 1620 S

The tool is switched on and off at the two-stage switch (7)

on the back of the grip handle. Airflow and temperature can

be adjusted to 2 settings. Stage 1 reaches 300 °C at an

airflow of 240 l/min, stage 2 reaches 500 °C at 450 l/min.

This tool is intended for home use only.

HL 1920 E

The tool is switched on and off at the two-stage switch (7)

on the back of the grip handle. In addition to three-stage

speed/airflow control (stage 1 is a cold-air stage at 80 °C),

temperature can be continuously adjusted over a range of

80 °C – 600 °C in settings 2 and 3 at the thumbwheel (8).

The numbers 1 - 9 on the thumbwheel serve as a guide

only. Whereas "1" means 80 °C, the maximum temperature

of 600 °C is attained at "9". Airflow can be adjusted to the

three stages of 150 / 150-300 / 300-500 l/min. The guard

sleeve (3) detaches at a bayonet catch.

HL 2020 E

The tool is switched on and off at the two-stage switch (7)

on the back of the grip handle. In addition to three-stage

speed/airflow control at the switch (7), temperature can be

continuously adjusted over a range of 80 °C to 630 °C in

settings 2 and 3 at the rocker switch (9). The target temper-

ature can be increased in 10 °C increments by pressing the

right-hand "+" side of the rocker switch (9) or reduced by

pressing the left-hand "-" side of the rocker switch (9).

Steinel HL2020E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info