Bedienungsanleitung Steinel IR 180 AP (Seite 9 von 43) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

592487

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

Functions

Adjusting screw left stop

position means: minimum

reach (approx. 1 m / factory

setting).

Adjusting screw right stop

positon means: maximum

reach (approx. 8 m).

(only for HF 360 AP)

Reach setting

(Sensitivity)

The term reach denotes the

approximately circular

diameter that results as the

detection zone.

1 - 8 m

Functions

LUX

Twilight setting

(Response threshold)

The desired sensor re-

sponse threshold can be

adjusted continuously from

approx. 2 lux to 2000 lux.

Adjusting screw right stop

position means: daylight

operation approx. 2000 lux

(factory setting).

2 - 2000 lux

Adjusting screw left stop

position means: night-time

operation approx. 2 lux.

When adjusting the detec-

tion zone and for the per-

formance test in daylight, the

adjusting screw must be set

to the RH stop position.

Time setting

(Switch/off delay)

The desired duration of illu-

mination of the connected

light can be continuously

adjusted from approx.

10 sec. to max. 30 min.

Adjusting screw left stop pos-

ition means: shortest time

approx. 10 sec. (factory set-

ting)

Adjusting screw right stop

position means: longest

time approx. 30 min.

The timer is restarted by

any motion detected before

this time elapses.

10 sec. - 30 min.

The shortest time setting is

recommended when adjus-

ting the detection zone and

performing a functional test.

Note: After every off switch-

ing, further motion detection

is interrupted for approx.

2 seconds. Only after this

time elapses is it possible

for the Sensor Switch to

switch light again.

Installation

Note for IR 180 AP:

The installation position

should be at least 1 m from

a light, since heat radiation

may trigger the system.

Installation procedure:

1. Loosen housing screws

and open housing a,

then loosen sensor unit

c (screw) and remove

with the basic element

2. Hold base of housing on

wall (with the inscription

TOP facing upwards)

and mark the drilling

holes.

3. Drill holes with a 6 mm

bit.

4. Insert dowels in the

holes.

5. Screw the base of the

housing in place with the

enclosed screws.

6. Strip the cable (approx.

70 mm) and remove

approx. 5 mm of insula-

tion from the flexible

ends.

7. Push through sealing

plugs and pass the ca-

ble through (the cable

sheath must be comple-

tely surrounded by the

sealing plug).

Connecting the supply

lead to the basic element

(refert to ill. on page 4):

The mains lead consists of

a 3 phase cable.

L = phase conductor (usu-

ally black or brown)

N = neutral conductor

(usually blue)

L’ = phase conductor (usu-

ally black or brown)

If in doubt, the cable must

be identified with a voltage

tester. Switch off the cur-

rent again. Phases (L) and

(L‘) in addition to the neu-

tral conductor (N) are con-

nected to the terminal

block. A protective-earth

conductor is not required.

Important: Reversing the

connections may result in

damage to the unit.

8. Insert basic element b

into the housing section

a (terminal connection

at bottom).

9. Carefully push on the

sensor module c (tak-

ing care not to jam) and

screw to the housing

base section.

10.After the mains connec-

tion has been made, the

sensor switch can be

operated (refer to func-

tions section).

11. Finally apply the design

shade d and screw in

place.

Note:

Parallel switching of

IR 180 AP and HF 360 AP

is possible. Nevertheless, a

neutral lead must be pres-

ent on each flush box. The

max. output to be switched

does not increase as a re-

sult.

lux

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel IR 180 AP Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info