Bedienungsanleitung Steinel IS 2180-5 (Seite 8 von 72) (Alle Sprachen)

593146

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

14 15

Safety precautions



Disconnect the power

supply before attempting

any work on the motion

detector.



During installation, the

electric power cable be-

ing connected must not

be live. Therefore, switch

off the power ﬁ rst and

use a voltage tester to

make sure the wiring

is off circuit.



Installing the sensor

involves work on the

mains power supply.

This

work must therefore be

carried out professionally

in accordance with the

applicable national wiring

regulations and electrical

operating conditions (

VDE 0100,

- ÖVE-EN 1,



- SEV 1000).



Please note that the

sensor must be protected

by a 10 A circuit breaker.

The mains supply lead

must be no greater than

10 mm in diameter.



Only carry out time and

twilight settings with the

lens ﬁ tted.

Principle

The IS 2180-5 is equipped

with two 120° pyro sensors

that detect the invisible heat

emitted from moving objects

(people, animals etc.). The

heat detected is electroni-

cally converted into a signal

that switches on loads (e.g. a

light) connected to it. Heat is

not detected through obs-

tacles, such. as walls or

panes of glass. Heat radia-

tion of this type will, there-

fore, not trigger the sensor.

The two pyro sensors

achieve a coverage angle of

180° with an aperture angle

of 90°. The lens can be re-

moved and turned, thereby

permitting two max. basic

reach settings of 8 m or 20

m. Using the wall mounts

provided with the unit, the

infrared sensor can easily be

ﬁ tted to internal and external

corners.

Important: The most reliable

way of detecting movement

is to install the unit with the

sensor aimed across the

direction in which a person

would walk and by ensuring

that no obstacles (such as

trees, walls etc.) obstruct the

line of sensor vision

Reach max. 20 m Reach max. 8 m

Direction of approach:

from the front

Direction of approach:

from the side

The site of installation should

be at least 50 cm from a light

because heat radiated from

it may trigger the sensor

unintentionally. To obtain the

speciﬁ ed ranges of 8/20 m,

the sensor should be installed

at a height of approx. 2 m.

Installation procedure:

1. Remove designer front trim

, 2. release clip  and fold

up lower half of enclosure, 3.

mark drill holes, 4. drill holes,

ﬁ t wall plugs (Ø 6 mm), 5. if

necessary, break open cable

entry if using surface-mount-

ed or concealed wiring.

6. Feed through mains and

load power supply lead and

connect. Use sealing plugs

for surface wiring.

a) Connect mains sup-

ply lead

The main supply leads is a

2 to 3-core cable:

L = phase

N = neutral conductor

PE = protective-earth

conductor

If you are in any doubt,

identify the conductors using

a voltage tester; then discon-

nect from the power supply

again. The phase (L) and neu-

tral conductor (N) are con-

nected according to terminal

assignment. The protective-

earth conductor is connected

to the earth terminal ( ).

A mains switch for switching

the unit ON and OFF may

of course be installed in the

mains supply lead. Alterna-

tively, you may use a normally

closed contact pushbutton to

activate the sensor manually

for the duration of the time

setting.

Note: The inside corner wall

mount can also be used

for wall installation with

surface-mounted power

supply lead. The cables can

be conveniently routed down

the surface of the wall behind

the unit and fed through the

cable entry.

Surface

wiring

Mains lead

Consumer lead

Supply cable, surface

wiring with wall mount

Concealed

wiring

Installation/Wall mounting

IS 2180-5_85x120_Zentraleuropa.indd 14-15IS 2180-5_85x120_Zentraleuropa.indd 14-15 17.12.13 14:2517.12.13 14:25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel IS 2180-5 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info