593146
11
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
20 21
Operation/Maintenance
The infrared sensor can be
used for switching light ON
and OFF automatically. The
unit is not suitable for burglar
alarm systems as it is not
tamperproof in the manner
prescribed for such systems.
Weather conditions may
affect the way the motion
detector works. Strong gusts
of wind, snow, rain or hail
may cause the light to come
ON when it is not wanted be-
cause the sensor is unable to
distinguish sudden changes
of temperature from sources
of heat. The detector lens
may be cleaned with a damp
cloth if it gets dirty (do not
use cleaning agents).
Connection examples
1. Light without neutral conductor 2. Light with neutral conductor
3. Connection using an indoor two-way switch
for manual override and automatic operation
Setting I: Automatic operation
Setting II: Manual operation, light permanently ON
Note: The system cannot be switched OFF, it is
only possible to select operation at setting I or II.
1) e. g. 1-4 x 100 W incandescent lamps
2) load, lighting 1000 W max. (refer to Technical specifi cations)
3) IS 2180-5 connection terminals
4) Indoor switch
5) Indoor two-circuit single interruption switch, manual operation, automatic operation
6) Indoor two-way switch, automatic operation, manual override
Troubleshooting
Malfunction Cause Remedy
IS 2180-5 without power
Fuse faulty, not switched
ON
Short circuit
Mains switch OFF
Replace fuse, turn ON
mains switch, check lead
with voltage tester
Check connections
Switch ON
IS 2180-5 will not switch ON
Twilight setting in night-
time mode during daytime
operation
Bulb faulty
Mains switch OFF
Fuse faulty
Detection zone not
properly targeted
Adjust setting
Change bulb
Switch ON
Fit new fuse, check
connection if necessary
Re-adjust
IS 2180-5 will not switch OFF
Continued movement in
detection zone
Light being operated is
located in detection zone
and keeps switching ON
as a result of temperature
change
Set to continuous opera-
tion by indoor two-circuit
single interruption switch
Check detection zone and
re-adjust if necessary or fi t
shrouds
Adjust detection zone or fi t
shrouds
Set two-circuit single inter-
ruption switch to automat-
ic operation
IS 2180-5 keeps switching
ON/OFF
Lamp being operated in
located the detection zone
Animals moving in
detection zone
Heat source (e.g. extractor
hood outlet) in detection
zone
Adjust detection zone or fi t
shrouds, increase distance
Adjust detection zone or fi t
shrouds
Adjust detection zone or fi t
shrouds
IS 2180-5 switches ON when
it should not
Wind is moving trees and
bushes in the detection
zone
Cars in the street are be-
ing detected
Sudden temperature
changes due to weather
(wind, rain, snow) or air
expelled from fans, open
windows
Fit shrouds to mask out
zones
Fit shrouds to mask out
zones
Change zone, move site of
installation
GB
IS 2180-5_85x120_Zentraleuropa.indd 20-21IS 2180-5_85x120_Zentraleuropa.indd 20-21 17.12.13 14:2517.12.13 14:25
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Steinel IS 2180-5 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info