Bedienungsanleitung Steinel IS 240 DUO (Seite 8 von 66) (Alle Sprachen)

592544

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

1514



y Disconnect the power supply

before attempting any work on

the motion detector.

y During installation, the electric

power cable to be connected must

be voltage-free.Therefore, switch

off the power first and check free-

dom from voltage with a voltage

detector.

y Installing the motion detector in-

volves work on the mains power

supply. This work must therefore be

carried out professionally in accord-

ance with the applicable national

wiring regulations and electrical

operating conditions (

- VDE

0100,

- ÖVE-EN 1,



- SEV

1000).

Safety instructions

Principle

Lights, alarms, and many other things

triggered by movement - for your con-

venience and safety.

Whether a house door, garage, patio

or carport, stairs, a storeroom or cellar

are involved, this infrared motion de-

tector is rapidly installed and ready for

operation anywhere.

The IS 240 DUO is equipped with two

120° pyro sensors which detect the

invisible heat emitted by moving ob-

jects (pedestrians, animals etc.).

The heat thus detected is electroni-

cally converted and switches ON con-

nected consumers (e.g. a light). No

heat radiation is detected through ob-

stacles, such as walls or glass and no

switching therefore occurs. The two

pyro sensors have a detection angle

of 240° with an opening angle of 180°.

Important: the safest motion detec-

tion is obtained when the device is

mounted and aligned laterally to the

walking direction and no obstacles

(such as trees and walls, for example)

obstruct the view.

Installation instructions

Installation

1) Supply lead

2) Service lead

3) Protective-earth

conductor

4) Lugs for surface-routed

supply lead

y Wall mounting

Warning: installation involves a

mains connection. With 230 V, a

risk of electrocution exists! There-

fore, switch off the power first and

check freedom from voltage with a

voltage tester. Installation of the

sensor involves work on the mains

power supply; this work must

therefore be carried out profession-

ally in accordance with regulations.

Please note that the motion detec-

tor must be protected by a 10 A cir-

cuit breaker.

The installation site should be at

least 50 cm from a light, since the

latter's heat radiation could result in

false triggering of the sensor. The

installation height should be ap-

prox. 2 m.

Unscrew the fastening screw 5

counterclockwise with a screw-

driver, slide down the mounting

plate 1 and remove it. Do not undo

the internal wiring to the terminal

block, but extract the block by

pulling it gently.

Insert the rubber plugs into the

mounting plate. Hold the mounting

plate against the wall and mark the

drill holes (paying attention to the

wiring arrangement in the wall), drill

the holes and insert the dowels.

In order to be able to perform a

switching operation, a power sup-

ply lead with at least two phases

must run to the unit and a second

lead out to the consumer. The two

rubber plugs can be pierced for this

purpose with a screwdriver.

Two lugs are provided on the bot-

tom of the wall fastener for surface

wiring. These can be snapped off

easily. After passing the wiring

through, the mounting plate can

be screwed in place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel IS 240 DUO Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Steinel IS 240 DUO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info