Bedienungsanleitung Steinel IS 300 (Seite 7 von 42) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Norwegisch, Finnisch)

593148

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Installation IS 300

Wall mounting

The installation site should be

at least 50 cm from a light,

since the latter's heat radi-

ation could result in false trig-

gering of the sensor. The in-

stallation height should be

approx. 2 m.

Unscrew the fastening screw

counterclockwise with a

screwdriver, slide down the

mounting plate and remove it.

Insert the rubber plugs into

the mounting plate. Hold the

mounting plate against the

wall and mark the drill holes

(paying attention to the wiring

arrangement in the wall), drill

the holes and insert the

dowels.

In order to be able to perform

a switching operation, a

power supply lead with at

least two phases must run to

the unit and a second lead

out to the consumer. The two

rubber plugs can be pierced

for this purpose with a screw-

driver. Two lugs are provided

on the bottom of the wall

fastener for surface wiring.

These can be snapped off

easily. After passing the wir-

ing through, the mounting

plate can be screwed in

place.

Connection of the leads:

The mains and consumer

leads consist of a 2 to 3 con-

ductor cable:

L, L‘ = live conductor or

switched phase to

the consumer

(usually black or

brown)

N = neutral conductor

(usually blue)

PE = protective-earth

conductor,

if present ( )

If in doubt, the conductors

must be identified with a

voltage tester. Switch off the

current again.

Wiring of the mains and con-

sumer conductors must be

performed in the wall holder

using the enclosed connect-

ing terminals:

1. The live conductor is in-

serted in the first terminal (L).

2. Both neutral conductors

(N) of the mains and con-

sumer leads are inserted into

the second terminal.

3. The switched phase to the

consumer (L‘) is inserted into

the third terminal.

4. Green/yellow protective-

earth conductors ( ) must

be inserted together into the

fourth terminal. In order to

identify the flexible leads, the

enclosed sticker ( ) must be

applied to one of the leads

(green/yellow).

Connection of the IS 300:

The connecting leads of the

IS 300 are to be inserted into

the connecting terminals ac-

cording to the marking on the

leads (L = black, N = blue,

L‘ = brown).

Important: Getting the

cable connections crossed

will produce a short circuit in

the unit or in your fuse box.

In this case, you must once

again identify the individual

wires and reconnect them.

A mains switch for ON and

OFF switching can of course

be installed in the mains lead.

1) Supply lead

2) Service lead

3) Protective-earth

conductor

4) Lugs for surface-

routed supply lead

5) Connecting lead

IS 300

black

blue

brown

green/yellow

Installation instructions



STEINEL infrared sensors

form the basis for modern

efficient crime deterrents.

They switch light on automat-

ically on sensing movement

within their detection zone

and therefore provide con-

venience and safety, while

making economical use of

energy.

Sensor housing

IS 300

Reach

Lens

Shroud

Fixing

screw

Decorative ring

Mounting plate

With a total of three integrated

pyro sensors, the IS 300 mo-

tion detector records the heat

and infrared radiation of mov-

ing bodies (people, animals,

etc.) which is invisible to the

human eye, within its detec-

tion zone. The recorded heat

radiation is converted elec-

tronically and one or several

connected consumers, e.g.

lights, are switched on

or off

again after a pre-program-

med time on leaving the de-

tection zone. No heat radia-

tion is detected through obs-

tacles, such as walls or glass

and no switching therefore

occurs. The IS 300 achieves

an angle of coverage of 300°

with an angle of aperture of

180°. It therefore covers a

detection zone of approx.

300 m

Important: The most reliable

motion detection is achieved

by mounting the unit diago-

nally to the direction of

movement and ensuring that

no obstacles (such as trees

or walls) obstruct the line of

sight.

Reach

12 m max.

1312

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel IS 300 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info