Functional Warranty
This STEINEL product has been manufactured with
great care, tested for proper operation and safety in
accordance with applicable regulations and then sub-
jected to random sample inspection. STEINEL guaran-
tees that it is in perfect condition and proper working
order. The warranty period is 36 months, starting on the
date of sale to the consumer. We will remedy defects
caused by material flaws or manufacturing faults. The
warranty will be met by repair or replacement at our own
discretion. The warranty shall not cover damage to wear
parts, damage or defects caused by improper treatment
or maintenance. Further consequential damage to exter-
nal items is excluded.
Claims under warranty shall only be accepted if the
product is sent fully assembled and well packed com-
plete with a brief description of the fault, a receipt or
invoice (date of purchase and dealer's stamp) to the
appropriate service centre.
Repair Service:
Please ask your nearest service centre
how to proceed for repairing faults not
covered by the warranty or occurring
after the warranty expires.
SensorLight switching ON when
it should not
Change in SensorLight reach
Red LED flashing rapidly
■
Wind is moving trees and bushes
in the detection zone
■
Cars in the street are being
detected
■
Sudden temperature change due
to weather (wind, rain, snow) or air
expelled from fans, open
windows
■
Change detection zone
■
Change detection zone
■
Change detection zone,
change site of installation
■
Differing ambient temperatures
■
Use shrouds to define detection
zone precisely
■
Internal fuse activated
■
Switch SensorLight OFF and back
ON again after 5 sec.
LED illuminated panel not operating
■
Terminal not pushed in all the way
■
Firmly press terminal together
LED illuminated panel OFF although
it is dark
■
Programme 3 or 4 selected
■
Change programme
LEDs flickering
■
Local power grid
■
see note on page 13
Troubleshooting
SensorLight without power
SensorLight will not switch ON
SensorLight will not switch OFF
Malfunction
■
Fuse faulty, not switched ON,
break in wiring
■
Short circuit
■
Fit new fuse; switch ON mains
switch; check wiring with voltage
tester
■
Check connections
■
Twilight control set to night-time
during daytime operation
■
Power switch OFF
■
Fuse faulty
■
Detection zone not properly
targeted
■
Internal electrical fuse has
been activated
(red LED flashing rapidly)
■
Mains terminal not connected
properly
■
Re-adjust (control
)
■
Switch ON
■
New fuse, check connection if
necessary
■
Re-adjust
■
Switch SensorLight OFF and
back ON again after 5 sec.
■
Firmly press terminal together
■
Continued movement within the
detection zone
■
Sensor unit is not properly
engaged
■
Check detection zone and
re-adjust if necessary
■
Lightly press sensor unit to
clip it into place
Basic lighting level does not go out
at about midnight as desired
■
External light source
(e.g. other motion detector or
light) inactivating the SensorLight
■
Shade SensorLight from extrane-
ous light, observe SensorLight for
several days as it takes time to
return to the correct value
SensorLight will not switch OFF
completely
■
Basic lighting level selected
■
Turn programme selector
dial to 1
Cause Remedy
- 15 -
Manual override function
If a mains switch is installed in the mains supply lead,
the light is capable of the following functions in addition
to the simple ON/OFF function:
Sensor operation
1) Switch light ON (when light is OFF):
Turn switch OFF and ON once.
Light stays ON for the period selected.
2) Switch light OFF (when light is ON):
Turn switch OFF and ON once.
The light goes out or switches over to sensor mode.
Manual override
1) Activate manual override:
Turn switch OFF and ON twice. The light is set to stay
ON for 4 hours (red LED lights up behind lens). Then it
returns automatically to sensor mode (red LED off).
2) Deactivate manual override:
Turn switch OFF and ON once. The light goes out or
switches over to sensor mode.
Important:
The switch should be actuated in rapid succession
(in the 0.5 – 1 sec. range).
Adjusting the detection zone
The detection zone can be limited to suit requirements.
The shrouds supplied with the light can be used to mask
out as many lens segments as you wish. This prevents
the light from being activated unintentionally, e.g. by
cars, passers-by etc., and allows you to target danger
spots. The shrouds can be cut along the pre-grooved
vertical divisions. Then you simply clip them onto the
lens.
Operation / Maintenance
The SensorLight is suitable for switching light ON auto-
matically. Weather conditions may affect the way the
SensorLight functions. Strong gusts of wind, snow, rain
or hail may cause the light to come ON when it is not
wanted because the sensor is unable to distinguish
sudden changes of temperature from sources of heat.
The detector lens may be cleaned with a damp cloth
if it gets dirty (do not use cleaning agents).
Technical specifications
Dimensions (H x W x D): 270 x 100 x 141 mm (L 626 LED)
270 x 328 x 141 mm (L 625 LED)
Mains voltage: 230 – 240 V, 50 Hz
Output: L 625 LED: 8 W LED main lighting
1 W LED street number lighting
155 lm
L 626 LED: 8 W LED main lighting
150 lm
Colour temperature: 3200 kelvin (warm white)
LED life expectancy: 50.000 hours
Angle of coverage: 360° with sneak-by guard
Detection reach: 8 m all round
Twilight setting: 2 – 2000 lux
Time setting: 5 sec. – 15 min.
Basic lighting level: 0 or 25%, soft light start
Manual override: 4 hours, switchable
IP rating: IP 44
Protection class: I
Temperature range: - 20° C to + 50° C
Declaration of conformity
- 14 -
This product complies with
- Low Voltage Directive 2006/95/EC
- EMC Directive 2004/108/EC
- RoHS Directive 2011/65/EC
GB
