Bedienungsanleitung Steinel L 840 SC (Seite 18 von 155) (Alle Sprachen)

758080

Zoom out

Zoom in

Vorherige Seite

1/155

Nächste Seite

- 35 -- 34 -

A microprocessor then issues the switch command "switch light ON". Detection

is possible through doors, panes of glass or thin walls. Analysing the signal,

the sensor distinguishes between moving persons and moving objects, such

as bushes or small animals. This rules out any inadvertent triggering by small

animals as well as interference from extreme temperatures.

The functions of the sensor-switched light can be set via smartphone and

tablet or control dial. Bluetooth interconnection is only possible via smartphone

or tablet.

Note: The high-frequency output of the iHF-sensor is approx. 1 mW – that's

1000 times less than the transmission power of a mobile phone or the output

of a microwave oven.

Package contents L 830, L 835, L 840SC/C(Fig.3.1)

– Luminaire

– Three screws

– Three wall plugs

– Three spacers

Product dimensions L 830SC/C(Fig.3.2)

Product dimensions L 835SC/C(Fig.3.3)

Product dimensions L 840SC/C(Fig.3.4)

Product components L 830, L 835, L 840SC/C(Fig.3.5)

A Wall mount

B Connecting terminal

C Sealing plug

D Plug connection

E Light cube

Package contents GL 80SC/C(Fig.3.6)

– Luminaire

– Proﬁle

– Base plate

– Four ﬂoor/ground screws

– Four wall plugs

– Four connecting screws

Product dimensions GL 80SC/C(Fig.3.7)

Product components GL 80SC/C(Fig.3.8)

A Cover cap

B Connecting terminal

D Plug connection

E Light cube

F Earth terminal

Luminous intensity distribution (Fig.3.9/3.10/3.11/3.12)

Reach (SC only) (Fig.3.13)

Note: If lights are mounted too close together, switching errors may occur as

the high-frequency signals emitted will interfere with each other. (Fig.3.14A)

The following measures will help to avoid switching errors of this kind:

• Allow a distance of at least 5 m between lights.

• Interconnect lights via the Smart Remote app and selectively deactivate the

sensor in individual lights via the Sensor-O function (Fig.3.14B + C). As

a result of interconnection, movement will also switch lights ON in spite of

their sensor being deactivated.

4. Electrical connection

Wiring diagram (Fig.4.1)

The mains supply lead is a 2 to 3-core cable:

L = phase conductor (usually black or brown)

N = neutral conductor (usually blue)

PE = protective-earth conductor (green/yellow)

If you are in any doubt, identify the conductors using a voltage tester; then

disconnect from the power supply again. Connect phase (L) and neutral con-

ductor (N) to the terminal. Insulate protective-earth conductor (PE) and place it

next to terminal block.

For GL 80SC/C, the protective-earth conductor must be connected to the

earth terminal (PE).

Important: Incorrectly wired connections will produce a short circuit later on

in the product or your fuse box. In this case, you must identify the individual ca-

bles and re-connect them. A mains power switch for turning the light ON and

OFF may of course be installed in the mains supply lead.

Important: The light source of this luminaire cannot be replaced. If the light

source needs to be replaced (e.g.at the end of its service life), the complete

luminaire must be replaced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel L 840 SC Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info