Bedienungsanleitung Steinel RS 10-4 L (Seite 7 von 52) (Alle Sprachen)

593315

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Installation

Important: Make sure the installation site is

not sub-

ject to

vibration.

Connecting a dimmer will result in damage to the

SensorLight.

Please note that the light must be protected by a 10 A

circuit breaker.

Installation procedure:

Before mounting the RS 21 L on the wall or ceiling,

first fit the glass shade clips and adjust the glass

shade (refer to drawing on page 3).

1. Hold enclosure against the wall/ceiling and

mark drill holes, paying attention to any existing

wiring in the wall/ceiling.

2. Drill the holes, insert wall plugs (6 mm dia.).

3. Fit and pierce sealing plug for mains supply lead.

4. Pass mains power supply lead though and fit the

heat-resistant wire insulator provided.

5. Screw enclosure into place.

6. Connecting the mains power supply lead (see fig.).

The mains power supply lead is a 3-core

cable:

L= phase conductor (usually black or brown)

N= neutral conductor (usually blue)

PE = protective earth conductor (green/yellow)

If you are in any doubt, identify the conductors using

a voltage tester; switch off the current again. Connect

the phase conductor (L) and neutral conductor (N) to

the terminal block. Insulate any PE protective earth

conductor with adhesive tape.

Technical specifications

Wattage: RS 14/15/16/16-x L: 60 W/E 27 max.

plus 100 VA max. (e.g. bathroom/WC fan extractor)

RS 10/10-x/13/21 L: 75 W/E 27 max.

RS 100/103 L: 100 W/E 27 max.

RS 104 - 110 L: 2 x 40 W/G 9 max.

plus 800 VA max. (e.g. bathroom/WC fan extractor)

Connection: 230 – 240 V, 50 Hz

Installation site: indoors, wall/ceiling mounting

HF system: 5.8 GHz CW radar, ISM band

Transmission power: approx. 1 mW

Detection: 360°, 160° opening angle, if necessary through glass, wood and stud walls

Reach: 1 – 8 m dia., infinitely variable

3 – 8 m dia. (RS 15 L, RS 16/16-2/16-3 L)

Time setting: 5 sec. to 15 min.

Twilight setting: 2 – 2000 lux

Enclosure: IP 44 (IP 20 RS 21 L)

Protection class: II

Power consumption: approx. 0.9 W

Temperature ranging from: - 10° C to + 50° C

- 13 -

Important: Reversing the connections will result in a

short-circuit in the light unit or in your fuse box later

on. In this case, you must identify the individual con-

ductors once again and re-connect them. A mains

switch for switching the unit ON and OFF may of

course be installed in the mains power supply lead.

7. Set functions , , .

8. Fit glass shade and secure in place either by turn-

ing or by means of the spring clips (RS 21 L).

Surface wiring:

Surface wiring may be carried out as illustrated in the

diagrams, no. 9 respectively, on pages 2 to 3.

Connection of an additional load

An additional load (100 VA maximum, e.g. bath-

room/WC fan extractor) may be connected to the

SensorLight and will then be switched on and off by

the sensor light's electronics. Screw the load's live

conductor to the terminal marked L’. First remove the

protective cap with a pair of pliers. The cables must

also be fitted with the heat-resistant wire insulator.

Loop neutral conductor (N) as well as any protective

earth conductor (PE) through from the distribution

box. ( see wiring diagram on page 4 )

Installation instructions

Dear Customer,

Congratulations on purchasing your new STEINEL

SensorLight and thank you for the confidence you

have shown in us. You have chosen a high-quality

product that has been manufactured, tested and

packed with the greatest care.

Please familiarise yourself with these instructions

before attempting to install the SensorLight because

prolonged reliable and trouble-free operation will only

be ensured if it is fitted properly.

We hope your new STEINEL SensorLight will bring

you lasting pleasure.

System components

Enclosure

Reach setting

(1 – 8 m dia.)*

Time setting

(5 sec. – 15 min.)

Twilight setting

(2 – 2000 lux)

HF sensor

Glass shade

Glass shade clips

(screw-fastenable)

Spring clip

Spacers for surface wiring

Metal shrouds (not for RS 16, RS 16-2,

RS 16-3, RS 15 L)

Snap ring for adjusting square glass shades

Principle

The SensorLight is an active motion detector. The

integrated HF sensor emits high-frequency electro-

magnetic waves (5.8 GHz) and receives their echo.

The sensor detects the change in echo from even

the slightest movement in the light's detection zone.

A microprocessor then triggers the "switch light ON"

command. Detection is possible through doors,

panes of glass or thin walls.

Detection zones for ceiling mounting:

1) Minimum reach (1 m dia.)*

2) Maximum reach (8 m dia.)*

Important: Persons or objects moving towards the

light are detected best.

Detection zones for wall mounting:

3) Minimum reach (1 m dia.)*

4) Maximum reach (8 m dia.)*

Safety warnings

■Disconnect the power supply before attempting any

work on the unit.

■The electrical connection lead must be dead during

installation. Therefore, switch off the power first and

check that the circuit is dead using a voltage tester.

■Installing the sensor light involves work on the

mains voltage supply. This work must therefore

be carried out professionally in accordance with

applicable national wiring regulations and electrical

operating conditions.

(

-VDE 0100,

-ÖVE /

ÖNORM E8001-1,



-SEV 1000)

Note:

The high-frequency output of the HF sensor is approx.

1 mW – that's just 1,000th of the transmission power

of a mobile phone or microwave oven.

approx. 1 mW approx. 1000 mW

- 12 -

* 3 – 8 m dia. (RS 15 L, RS 16/16-2/16-3 L)

BDAL Serie RS_24spr_neu 27.07.2011 11:06 Uhr Seite 13

Steinel RS 10-4 L Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info