Bedienungsanleitung Steinel RS 50 (Seite 6 von 51) (Alle Sprachen)

593313

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

The SensorLight can be put into operation as soon as

the enclosure  has been fitted and the SensorLight

has been connected to the mains power supply.

Putting the light into operation manually at the light

switch turns it OFF after 10 secs. for the calibration

phase. Once calibrated, it is activated for the sensor

mode. It is not necessary to operate the light switch

a second time.

Reach setting (sensitivity)

Reach is the term used to describe the

diameter of the more or less circular

detection zone produced on the

ground after mounting the sensor

light at a height of 2.5 m. Turn the

reach control  fully anticlockwise to

select minimum reach (approx. 1 m

dia.)*, and fully clockwise to select maximum reach

(approx. 8 m dia.)*. (The light leaves the factory set to

maximum reach.)

Time setting (switch-off delay)

The light can be set to stay ON for

any period of time between approx.

1 min. (control  turned fully anti-

clockwise) and a maximum of 15 min.

(control  turned fully clockwise).

(The light leaves the factory set to the

shortest time.) Any movement detect-

ed before this time elapses will re-start the timer. It is

recommended to select the shortest time for adjusting

the detection zone and for performing the walk test.

Note: After the light switches OFF, it takes approx.

1 sec. before it is able to start detecting movement

again. The light will only switch ON in response to

movement once this period has elapsed.

Twilight setting (response threshold)

The chosen light response threshold

can be infinitely varied from approx.

2 – 2000 lux. Turn control  fully

anticlockwise to select dusk-to-dawn

operation at about 2 lux. Turn control

 fully clockwise to select daylight

operation at about 2000 lux. (The

light leaves the factory set to daylight operation.) The

control must be turned fully clockwise when adjusting

the detection zone and performing the walk test in

daylight.

Functions

- 11 -

1 m – 8 m dia.*

Functional Warranty

This STEINEL product has been manufactured with

great care, tested for proper operation and safety in

accordance with applicable regulations and then sub-

jected to random sample inspection. STEINEL guar-

antees that it is perfect condition and proper working

order. The warranty period is 36 months, starting on

the date of sale to the consumer. We will remedy

defects caused by material flaws or manufacturing

faults. The warranty will be met by repair or replace-

ment at our own discretion. The warranty shall not

cover damage to wear parts, damage or defects

caused by improper treatment or maintenance.

Further consequential damage to other objects is

excluded.

Claims under the warranty will only be accepted if the

unit is sent fully assembled and well packed complete

with a brief description of the fault, a receipt or

invoice (date of purchase and dealer's stamp) to the

appropriate Service Centre.

Repair Service:

Our Customer Service Department

will repair faults not covered by

warranty or after the warranty period.

Please send the product well packed

to your nearest Service Centre.

Declaration of conformity

This product complies with Low Voltage Directive

2006/95/EC, EMC Directive 2004/108/EC,

RoHS Directive 2002/95/EC and RTTE Directive

1999/05/EC.

1 min. – 15 min.

2 – 2000 lux

Installation

Important: Make sure the installation site is not sub-

ject to vibration.

Connecting a dimmer will result in damage to the

SensorLight.

Please note that the light must be protected by a 10 A

circuit breaker.

1. Hold enclosure  against the wall/ceiling and

mark drill holes, paying attention to any existing

wiring in the wall/ceiling.

2. Drill the holes, insert wall plugs (6 mm dia.).

3. Fit and pierce sealing plug for mains supply lead.

4. Pass mains power supply lead though and fit the

heat-resistant wire insulator provided.

5. Screw enclosure  into place.

6. Connecting the mains power supply lead (see fig.).

The mains power supply lead is a 3-core cable:

L = phase conductor (usually black or brown)

N = neutral conductor (usually blue)

PE = protective earth conductor (green/yellow)

If you are in any doubt, identify the conductors using

a voltage tester; switch OFF the current again.

Connect the phase conductor (L) and neutral

conductor (N) to the terminal block. Insulate any PE

protective earth conductor with adhesive tape.

Technical specifications

Wattage: 1 x 13 watts (TC-DEL G24-Q1) *

plus max. of 100 W (e.g. bathroom/WC extractor fan)

5 x RS 50 max.

Connection: 230 – 240 V, 50 Hz

Installation site: indoors, wall/ceiling mounting

HF-system: 5.8 GHz CW radar, ISM band

Transmission power: approx. 1 mW

Detection: 360°, 160° opening angle, if necessary through glass, wood and stud walls

Reach: 1 – 8 m all round, infinitely variable

Time setting: 1 min. to 15 min.

Twilight setting: 2 – 2000 lux

Enclosure: IP 44

Protection class: II

Power consumption: approx. 0.9 W

Temperature range: -10°C to + 50°C

must only be operated with the bulb specified; bulb life is not affected by the light switching ON and OFF.

- 10 -

Important: Reversing the connections will result in a

short-circuit in the light unit or in your fuse box later

on. In this case, you must identify the individual con-

ductors once again and re-connect them. A mains

switch for switching the unit ON and OFF may of

course be installed in the mains power supply lead.

7. Set functions , , .

8. Fit shade and secure in place by rotating.

Surface wiring:

Surface wiring can be carried out as shown in the

diagrams on page 2.

Connection of an additional load

An additional load (e.g. bathroom/WC fan extractor)

may be connected to the SensorLight and will then

be switched ON and OFF by the SensorLight's elec-

tronics. Screw the load's live conductor to the termi-

nal marked L’. First remove the protective cap with a

pair of pliers. The cables must also be fitted with the

heat-resistant wire insulator. Loop neutral conductor

(N) as well as any protective earth conductor (PE)

through from the distribution box (see wiring diagram

on page 3).

Tip!

least

5 min.

BDAL_RS 50_24spr.qxd 01.12.2010 14:44 Uhr Seite 11

Steinel RS 50 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info