Bedienungsanleitung Steinel RS PRO 5500 (Seite 6 von 51) (Alle Sprachen)

593348

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

- 10 - - 11 -

Technical specifications

RS PRO 5500 sensor/slave

Dimensions (H x W x D):

1295 x 161 x 64 mm

Mains power connection: 230 – 240 V/50 Hz

Output:

2 x 28 Watt / T5 *

Additional switching capacity: - 1000 W max. (resistive load, e.g. filament bulb)

- 400 W max. (uncorrected, inductive,

cos φ = 0.5, e.g. fluorescent lamps)

- 400 W max. (electronic ballasts, capacitive,

e.g. low-energy lamps, max. of 4 x 28 W, C ≤ 132 F)

HF-system: 5.8 GHz (responds to the tiniest movement regardless of temperature) *

Angle of coverage: 360°, 160° angle of aperture *

(if applicable, through glass, wood or stud walls)

Transmission power: approx. 1 mW *

Reach: infinitely variable from 1 – 8 m dia. (in 4 directions) *

Max. area covered approx. 50 m

Time setting: 1 min. – 20 mins. *

Twilight setting: 2 – 2000 lux *

Enclosure: IP 41 / IP 44 (when ceiling mounted)

Protection class: I

Power consumption: 0.9 W

Lamp life is not affected by being switched "ON" and "OFF".

For sensor-control version only

Installation

Connecting the mains power supply lead (see Fig.).

The mains lead consists of a 3-phase cable.

L = phase conductor (usually black or brown)

N = neutral conductor (usually blue)

PE = protective-earth conductor (green/yellow)

If you are in any doubt, identify the conductors using a

voltage tester; then switch "OFF" the power again.

Important: Reversing the connections will result in a

short-circuit in the light unit or in your fuse box later

on. In this case, you must identify the individual con-

ductors once again and re-connect them.

A mains switch for switching the unit "ON" and "OFF"

may of course be installed in the mains power supply

lead.

Important: Make sure the installation site is

not

subject to

vibration.

Connecting a dimmer will result in damage to the

SensorLight.

Please note that the light must be protected by a 10 A

circuit breaker.

L’ Connection of an additional load:

An additional load with max. 800 W can be con-

nected to the SensorLight, switched by the electronics.

Screw the live conductor to the load into the terminal

marked L’ on the SensorLight. Clamp the neutral

conductor in the terminal marked N together with the

neutral conductor of the mains power supply lead.

Attach the protective-earth conductor to the earth

terminal.

The SensorLight can be put into service after mount-

ing the light and connecting it to the mains power

supply. When putting the light into operation manually

at the light switch, it will switch "OFF" after 10 sec. for

the calibration phase and is then activated for sensor

mode. It is not necessary to operate the light switch

a second time.

Reach setting (sensitivity)



Reach is the term used to describe

the diameter of the more or less

circular detection zone produced

on the ground after mounting the

SensorLight at a height of 2.5 m.

Turn the reach control fully anti-

clockwise to select minimum reach

(approx. 1 m dia.), and fully clockwise to select max-

imum reach (approx. 8 m dia.). (The light leaves the

factory set to maximum reach.)

Functions

1 m–8 m dia.

Time setting (switch-off delay)



The light can be set to stay "ON" for

any period of time between approx.

1 min. (control turned fully anticlock-

wise) and a maximum of 20 mins.

(control turned fully clockwise). (The

luminaire leaves the factory set to

the shortest time.) Any movement

detected before this time elapses will re-start the

timer. It is recommended to select the shortest time

for adjusting the detection zone and for performing

the walk test.

Note: After the light switches "OFF", it takes approx.

1 second before it is able to start detecting movement

again. The light will only switch "ON" in response to

movement once this period has elapsed.

Twilight setting (sensor response threshold)



You can set the light to come "ON"

at any light level from approx.

2 – 2000 lux. Turned fully anti-

clockwise, the control is set to dusk-

to-dawn operation at approx. 2 lux.

Turned fully clockwise, the control is

set to daylight operation at approx.

2000 lux. (The light leaves the factory set to daylight

operation.) The control must be turned fully clockwise

when adjusting the detection zone and performing

the walk test in daylight.

Note: Apart from in the daylight setting, the luminaire

switches "OFF" once an hour for 1 second at all other

twilight settings to measure the current twilight.

Hint: The easiest way of finding the desired light

threshold is to start by waiting for the surrounding

brightness at which the light function is to be acti-

vated. Set the control dial to the fully anti-clockwise

position and allow the light to switch "OFF". Now

turn the control clockwise and let go as soon as the

luminaire has switched the light "ON". From now on,

the luminaire will always switch "ON" and "OFF" under

these light conditions.

1 min. – 20 min.

Recommendation:

To ensure trouble-free HF-sensor operation, we

recommend seasoning the tubes by leaving them

switched

"ON" for 100 hours. This seasoning

process can increase tube life.

1. Connect light and switch "ON"

2. Turn all 3 setting controls fully clockwise, then turn

the middle setting control fully anticlockwise and fully

clockwise again (within 10 sec.)

The seasoning process is confirmed by switching the

light "OFF" twice and then back "ON" again.

4. Now turn all controls to the chosen settings.

5. The light is now left "ON" for 100 hours without

sensor function. Do not disconnect the light from the

mains power supply during this period.

6. The luminaire automatically returns to sensor mode

after 100 hours.

Note:

If tubes are not seasoned or ambient temperatures are

low, the sensor may not switch the light "OFF". In this

case, switch the light "OFF" and, for the time being,

drastically reduce the reach setting.

Please only use high-quality branded lamps.

Otherwise, we cannot guarantee that the high-

precision sensor will operate reliably.

Tip:

Using the remote control, functions can be comfort-

ably set on the floor.

2 - 2000 lux

Accessories

Remote control for RS PRO EAN No.: 400784173781

(optional, not included in delivery).

Declaration of Conformity

This product complies with

- Low Voltage Directive 2006/95/EC

- EMC Directive 2004/108/EC

- RoHS Directive 2011/65/EC

- R&TTE Directive 1999/05/EC

- WEEE Directive 2012/19/EC

Steinel RS PRO 5500 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info