Bedienungsanleitung Steinel RS PRO LED Q1 (Seite 6 von 8) (Alle Sprachen)

593290

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

- 10 - - 11 -

1� About This Document

Please read carefully and keep in a safe place�

– Under copyright. Reproduction either in whole or

in part only with our consent.

– Subject to change in the interest of technical

progress.

Symbols

Hazard warning!

...

Reference to other information in the

document�

2� General Safety Notiﬁcation

• Disconnect the power supply before attempting

any work on the unit.

• During installation, the electric power cable to be

connected must not be live. Therefore, switch off

the power ﬁrst and use a voltage tester to make

sure the wiring is off-circuit.

• Installing the sensor-switched light involves work

on the mains supply voltage.

This work must therefore be carried out pro-

fessionally in accordance with national wiring

regulations and electrical operating conditions.

(

- VDE 0100,

- ÖVE / ÖNORM E8001-1,

- SEV 1000)

• Only use genuine replacement parts.

• Repairs may only be made by specialist work-

shops.

3� RS PRO LED Q1

The sensor-switched indoor light is an efﬁcient light

that controls itself. A high-frequency sensor for

detecting persons, a light sensor for identifying the

room's lighting situation as well as LEDs requiring no

maintenance provide efﬁcient, instantaneous light.

Several lights in one room can be networked into a

group via the 868MHz wireless communication unit

(channel selection). Wireless communication to the

next light functions reliably over a distance of 50 m.

All lights then operate with equal rights and act as

one overall light.

Optionally, all function settings can be made via the

RC10 remote control (➔ "8� Accessories")

The sensor-switched light is an active motion

detector. The integrated HF sensor emits high-

frequency electromagnetic waves (5.8GHz) and

receives their echo. The change in echo caused by

the slightest movement within the detection zone of

the light is detected by the sensor. A microproces-

sor then issues the switch command "switch light

ON". Detection is possible through doors, panes of

glass or thin walls.

Detection zones:

1) Minimum reach (Ø 1 m)

2) Maximum reach (Ø 8 m)

Note:

The high-frequency power of the HF sensor is

approximately 1mW – 1000 times less than the

transmission power of a mobile phone or micro-

wave oven.

Package contents (Fig� 3�1)

Product dimensions (Fig� 3�2)

Device overview (Fig� 3�3)

A Ceiling mount

B DIP switches

Channel selection

Dimming function

C Twilight setting

D Time setting

E Reach setting

F Plug connection

G Light enclosure

H Retaining screws

4� Installation

• Switch OFF power supply (Fig� 4�1)

Connect the mains power supply lead (Fig� 4�2)

The mains power supply lead is a 3-core cable:

L = phase conductor

(usually black, brown or grey)

N = neutral conductor (usually blue)

PE = protective-earth conductor (green/yellow)

If you are in any doubt, identify the conductors using

a voltage tester; then disconnect from the power

supply again. Connect phase (L) and neutral con-

ductor (N) to the terminal block.

Important:

Incorrectly wired connections will produce a short

circuit later on in the product or your fuse box. In

this case, you must identify the individual conduc-

tors once again and re-connect them. A mains

power switch for turning the unit ON and OFF may

of course be installed in the mains supply lead.

5� Mounting

• Check all components for damage.

• Do not use the product if it is damaged

Mounting procedure

• Select appropriate mounting location, taking the

reach and motion detection into consideration

• Switch OFF power supply (Fig� 4�1)

• Mark drill holes (Fig� 5�2)

– Drill holes and insert screw anchors (Fig� 5�3)

– Directly via the connection socket (Fig� 5�3)

– With spacers for surface-mounted cables

(Fig� 5�4)

• Connect conductors (Fig� 4�2)

• Switch ON power supply (Fig� 5�5)

• Make potentiometer settings (Fig. 5�6)

➔ "6. Functions"

• Set DIP switches (Fig� 5�7)

➔ "6� Functions"

• Fit light enclosure (G) onto ceiling mount (A) and

clip into place. Pay attention to plug connection

(F) (Fig� 5�8).

• Screw in retaining screws (H)

approx� 1mW approx� 1000mW

6� Function

After the ceiling mount has been installed and the

mains connection has been made, the sen-

sor-switched light is ready for use. When putting

the light into operation manually at the light switch,

it will switch OFF after 10seconds for the calibra-

tion phase and is then activated for sensor mode.

It is not necessary to operate the light switch a

second time.

Potentiometer function (Fig� 5�6)

Reach setting (sensitivity) (E)

Factory setting: 8m

Reach is the term used to describe the diameter of

the more or less circular detection zone produced

on the ground after mounting the sensor-switched

light at a height of 2.5m.

– Potentiometer set to maximum = max. reach

(approx. Ø 8 m)

– Potentiometer set to minimum = min. reach

(approx. Ø1m)

Potentiometersetto"•"= sensor OFF

Motion detection and all other sensor functions are

completely deactivated. In this setting, the light can

be used as a normal light and turned ON and OFF

at the light switch (DIP 1-5 = OFF).

Limiting reach

By ﬁtting the shrouds supplied with the light, the

reaches can be reduced in four directions

(Fig� 6�1 to 6�4).

Time setting (stay-ON time) (D)

Factory setting: 5 seconds

The light's ON time can be set to any period from

approx. 5seconds to a maximum of 15minutes.

Any movement detected before this time elapses

will restart the timer.

Note: After the light switches OFF, motion detection

is interrupted for approximately 1second. The light

will only switch ON in response to movement once

this period has elapsed.

Twilight setting (response threshold) (C)

Factory setting: 2000 lux

The light's chosen response threshold can be inﬁnite-

ly varied from approximately 2 to 2000 lux.

– Control dial set to = daylight operating mode

(depending on ambient light level)

– Control dial set to = night-time operation

(approx. 2lux)

Steinel RS PRO LED Q1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info