Bedienungsanleitung Steinel sensIQ (Seite 8 von 68) (Alle Sprachen)

593132

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

- 15 -

Troubleshooting

Functional Warranty

This Steinel product has been manufactured with the

utmost care, tested for proper operation and safety in

accordance with applicable regulations and then subjected

to random sample inspection. STEINEL guarantees that it

is in perfect condition and proper working order.

The warranty period is 36 months, starting on the date of

sale to the consumer. We will remedy defects caused by

material flaws or manufacturing faults. The warranty will

be met by repair or replacement of defective parts at our

own discretion. The warranty does not cover damage to

wear parts, nor does it cover damage or defects caused

by improper treatment, maintenance or the use on non-

genuine parts. Further consequential damage to other

objects shall be excluded.

Claims under warranty shall only be accepted if the product

is sent fully assembled and well packed complete with a

brief description of the fault, a receipt or invoice (date of

purchase and dealer's stamp) to the appropriate service

centre.

Repair Service:

Please ask your nearest service

centre how to proceed for repairing

faults not covered by the warranty

or occurring after the warranty

expires.

Malfunction Cause Remedy

Sensor without power ■ Fuse faulty, not switched ON,

break in wiring

■ Short circuit

■ New fuse, turn on power switch,

check wiring with voltage tester

■ Check connections

Sensor will not switch ON ■ Twilight control set to night-time

mode during daytime operation

■ Bulb faulty

■ Power switch OFF

■ Fuse faulty

■ Detection zone not properly

targeted

■ Adjust setting

■ Change bulb

■ Switch ON

■ Fit new fuse, check connection

if necessary

■ Re-adjust

Sensor will not switch OFF ■ Permanent movement in the

detection zone

■ Light being operated in the

detection zone causing sensor

to respond as a result of change

in temperature

■ Light being operated is in the

manual override mode (LED ON)

■ Check zone, adjusting if

necessary, or shroud

■ Change zone, or shroud

■ Deactivate manual override

Sensor keeps switching ON/OFF ■ Lamp being operated in the

detection zone

■ Animals moving in the detection

zone

■ Change zone, shroud or increase

distance

■ Change zone, or shroud

Sensor responds when it should not ■ Wind is moving trees and bushes

in the detection zone

■ Cars in the street are being

detected

■ Sunlight shining on the lens

■ Sudden temperature changes due

to weather (wind, rain, snow) or air

expelled from fans, open windows

■ Change zone

■ Mount sensor in a protected

place or change zone

■ Change zone, change site of

installation

Change in sensor's reach ■ Differing ambient temperatures ■ Adjust reach by reach controller

, apply shroud foils  if appro-

priate

LED flashes rapidly when a remote

control button is pressed

■ Remote control not "taught" ■ Disconnect the sensor from the

power supply for approx. 5 sec.

Switch on the voltage again and

press the button on the remote

control within 10 min.

Sensor

- 14 -

Functions by infrared remote control

Any number of sensIQ can be controlled by remote

control.

Note: Each sensIQ has a maximum of one remote

control. When the remote control is used for the first

time, the latter must be "taught". In order to do this,

the button must be pressed within 10 min. of switch-

ing on the supply voltage. This operation can be repeat-

ed as often as desired.

The last remote control saved always applies.

LED display

Each valid press of the button is indicated by a single

flash of the red LED behind the lens. The LED sensor

display is subsequently deactivated for approx. 5 sec.

If the remote control has not yet been "taught", the LED

flashes rapidly 3x at each press of the button.

The following special functions are presented as follows:

Holiday function: LED flashes rapidly 3x every 5 sec.

Manual override: LED permanently ON

Permanent light OFF: LED flashes every 2 sec.

Reset function:

Press once to quit the holiday, manual override and

permanent light OFF functions. The previously set

values apply again.

Holiday function:

The holiday function simulates presence. Once the twi-

light threshold is reached, the connected load is pro-

grammed to switch ON and OFF for periods of approx.

3 hours. Normal sensor mode remains active.

LED display: 3 x rapid flashing every 5 sec.

ON time:

By pressing, the connected light fixture is switched ON

for 4 hours. The sensor subsequently returns to sensor

mode automatically.

LED display: permanently ON.

Permanent light OFF:

By pressing, the connected light fixture is switched OFF

for 6 hours. The sensor subsequently returns to sensor

mode automatically.

LED display: flashes every 2 sec.

Twilight setting by memory button:

Under desired light conditions in which the sensor

should subsequently react to movement, the button

should be pressed. The current twilight value is saved.

Twilight setting by the potentiometer on

the device:

By pressing the button, the twilight value set on the

sensor is applied again. As soon as you change the

twilight setting on the device, this value will be adopted.

Any adjustments of the remote control are ineffective.

When using the "soft start" mode, the following

additional functions are available for filament bulbs:

Soft start / end:

By pressing the button, any activated basic brightness

is deleted.

Basic brightness:

By pressing the button once, permanent illumination at

night with approx. 25% light output is achieved.

Basic brightness (until the middle of the night):

As basic brightness; however the constant light of 25 %

output switches OFF from approx. the middle of the

night.

Sensor

Modules as accessories

The soft start module is available as an accessory.

It offers:

1. Softly switching light ON and OFF

2. Basic brightness in the dark

(only until the middle of the night if desired).

Do not use low-energy bulbs or fluorescent lamps in

conjunction with the SoftStart module.

The soft start module is suitable for connection of an

additional light fixture of max. 100 W. Soft start and

dimming are performed with trailing edge.

With wireless modules one or several sensIQ and

RS PRO 1000 sensors and/or slave lights can be

connected to form switching groups.

A fixed cable connection by means of a switching lead

is then no longer required.

This floating module provides the capability of using a

floating output on the sensIQ for operating independent

devices or systems.

SensIQ_26spr_14-08-13_SensIQ_24spr.qxp 20.08.13 14:42 Seite 15

Steinel sensIQ Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info