Bedienungsanleitung Stiebel Eltron CK 20 Trend LCD - 236653 (Seite 21 von 92) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

739443

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

www.stiebel-eltron.com CK 20 Trend LCD | 21

OPERATION | INSTALLATION

Troubleshooting

Dust ﬁlter cleaning

 Clean the dust ﬁlter at regular intervals. The dust ﬁlter can

be pulled out from the side of the appliance.

You may need to detach the appliance from the wall mount-

ing bracket beforehand (see chapter "Preparations/ Installa-

tion site").

D0000069514

8. Troubleshooting

Problem Cause Remedy

The appliance does

not deliver the

required heating

output.

The dust filter is heavily

soiled.

Check and, if necessary,

clean the dust filter.

Room does not get

warm enough. Ap-

pliance does not get

hot.

Temperature set too low

on the appliance.

Check the temperature set

on the appliance. Adjust if

necessary.

No power supply. Check the RCD and the fuse/

MCB in the fuse box.

Fuse has blown. Appliance cannot be re-

started.

Room does not get

warm enough al-

though the appliance

is hot.

Overheating. High limit

safety cut-out limits

heating output.

Eliminate the cause (dirt or

obstructions at the air inlet

or outlet). Observe minimum

clearances.

The heat demand of the

room is higher than the

appliance output.

Remedy heat losses (Close

windows and doors. Avoid

constant venting.)

The room gets too

hot.

The appliance tempera-

ture is set too high.

Check the selected room

temperature. Adjust if nec-

essary.

Detected room tempera-

ture does not match actu-

al room temperature.

Avoid obstructions to air

changes between appliance

and indoor air.

Window open de-

tection does not

respond.

Appliance does not detect

a pronounced tempera-

ture drop when venting.

(Window open detection

requires a previously sta-

ble room temperature.)

Wait a while after making

settings on the appliance,

until the room temperature

has fully stabilised.

Avoid obstructions to air

changes between appliance

and indoor air.

Manually switch the appli-

ance to standby mode for the

duration of venting.

Window open detection

is not enabled.

Switch on window open de-

tection in the standard menu.

"Adaptive start" func-

tion does not work as

required.

This function is only ef-

fective in timer mode.

Use the timer mode for opti-

mised heating convenience.

Severely fluctuating room

temperature or the appli-

ance learning procedure

has not been completed.

Wait a few days for the be-

haviour to stabilise.

"Adaptive start" function

is not enabled.

Switch on the "Adaptive

start" function in the stand-

ard menu.

"Err" or "E..." is dis-

played.

Internal fault detected. Notify the qualified con-

tractor.

If you cannot remedy the fault, contact your qualiﬁed contractor.

To facilitate and speed up your request, provide the number from

the type plate (000000-0000-000000).

INSTALLATION

9. Safety

Only a qualiﬁed contractor should carry out installation, commis-

sioning, maintenance and repair of the appliance.

9.1 General safety instructions

We guarantee trouble-free function and operational reliability only

if original accessories and spare parts intended for the appliance

are used.

9.2 Instructions, standards and regulations

Note

Observe all applicable national and regional regulations

and instructions.

- Install the appliance in such a way that control equipment

cannot be touched by a person in the bath or shower.

- All electrical connection and installation work must be car-

ried out in accordance with VDE regulations (DIN VDE 0100)

[or local regulations], the rules of your local power supply

utility, and relevant national and local regulations.

- Only mount the appliance on a vertical wall that is tempera-

ture-resistant to at least 85°C.

- Maintain minimum clearances to adjacent surfaces.

- Ensure the on-site cable has an adequate cross-section.

- If connecting the appliance via a socket, ensure that this is

easily accessible once the appliance has been installed.

- Never install the appliance directly below a wall socket.

- When installing the heating appliance in rooms with a bath

or shower, observe the safety zone according to VDE 0100,

section 701 [or local regulations], in accordance with the de-

tails on the appliance type plate.

- Observe the type plate. The speciﬁed voltage must match the

mains voltage.

- Observe the Building and Garage Regulations [or local

regulations].

10. Appliance description

10.1 Standard delivery

The following are delivered with the appliance:

- 1 wall mounting bracket

10.2 Accessories

- Towel holder

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiebel Eltron CK 20 Trend LCD - 236653 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info