Bedienungsanleitung Stiebel Eltron CNS200F (Seite 14 von 76) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

469623

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

HTV`.HC

TT<.CZV.T`.HC

ĜÔCZ% qqqĪZ`.<é<`VHCĪHB

Never step on the appliance.

When using the mobile ﬂoorstanding unit, observe

the following:

— Never cover the power cable with a carpet or

rug. Route the power cable away from walkways

to prevent anyone tripping over the cable or

knocking the appliance over.

— Avoid using an extension cable. If this is

unavoidable, only use an undamaged extension

cable with a sufﬁcient cable cross-section for

the full appliance output, as well as undamaged

plugs or coupler plugs and adequate protective

measures.

— Position the appliance on a solid base. On a

soft base, the appliance can tip over or the air

apertures can become blocked.

— Never move or carry the appliance by pulling on

the power cable.

— If you use the appliance as a ﬂoorstanding unit,

never install it in the bathroom, in similarly damp

rooms or outside.

2.3 CE designation

The CE designation shows that the appliance meets all essential

requirements according to the:

—Electromagnetic Compatibility Directive

—Low Voltage Directive

2.4 Test symbols

See type plate.

The type plate is located on the right on the exterior of the

appliance.

3. Appliance description

The appliance is an electric direct heater and can be used as a

wall mounted appliance or alternatively as a mobile ﬂoorstanding

appliance with feet attached.

The appliance is suitable as a full heating system in bathrooms,

for example, or for use between seasons and as a booster heater

in smaller rooms, such as hobby and guest rooms.

The air in the appliance is heated by a heating element and

expelled via natural convection through the air outlet grille at the

top. Cool room air ﬂows in through the apertures at the bottom

of the appliance.

After mounting the appliance to the wall or attaching the feet, and

making the electrical connection via the mains plug, the appliance

is ready for operation.

4. Operation

4.1 Description of the user interface

» Switch the appliance ON via the switch on the r.h. side of the

appliance.

» Set the required room temperature via the continuously variable

temperature selector (for temperatures see specification

chapter).

26_07_31_0037

As soon as the selected room temperature is reached, it is

constantly maintained at this selected temperature through

periodic heating (the output of the appliance must correspond at

least to the required heat demand of the room).

If several appliances are installed in a single room, the setting

at the temperature selector on each appliance can be different.

To avoid excessive power consumption when windows are open,

you should stop the appliance while venting.

4.2 Frost protection

» Turn the temperature selector as far to the right as possible. In

this position, the temperature controller switches on the heating

element automatically if the room temperature drops below the

frost protection temperature.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiebel Eltron CNS200F Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info