Bedienungsanleitung Stiebel Eltron DHB-E 13 A (Seite 4 von 20) (Englisch)

650333

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite





 

3. Appliance description

This electronically controlled instantaneous water heater with

automatic output matching keeps the outlet temperature constant.

This occurs regardless of the inlet temperature up to the output

limit. The DHW outlet temperature can be freely selected.

The bare wire heating system is suitable for hard and soft water

areas; it has low susceptibility to scale build-up. The heating

system ensures quick and efﬁcient DHW availability.

4. Operation

4.1 Temperature selector

DHB-E ... SLi

26�02�02�1381

DHB-E ... A

26�02�02�1382

Should the outlet temperature fail to reach the required level with

the draw-off valve fully open and the temperature selector set to

maximum, then more water ﬂows through the appliance than can

be heated by the heating element.

 Reduce the ﬂow rate with the draw-off valve.

4.2 Draw-off capacities

Subject to season, varying maximum mixed water or draw-off

capacities result from different cold water temperatures. Further

information can be found in the chapter "Speciﬁcation".

4.3 Thermostatic valve

We recommend adjusting the appliance to the maximum

temperature setting.

4.4 Temperature limit/Anti-scalding protection

The maximum outlet temperature for the appliance can be limited

to 43°C. Refer in this case to your local heating contractor.

5. Cleaning, care and maintenance

 Never use abrasive or corrosive cleaning agents. A damp

cloth is sufﬁcient for cleaning the appliance.

Maintenance work, such as checking the electrical safety, must

only be carried out by a heating contractor.

6. Troubleshooting

Material damage

Following an interruption of the water supply,

recommission the appliance by carrying out the following

steps, in order to prevent the destruction of the bare wire

heating system.

 Disconnect the appliance from the power supply by

removing the fuses/tripping the MCBs.

 Open the tap until the appliance and its upstream

cold water inlet line are free of air.

 Switch the mains power back ON again.

  

The appliance will not

start in spite of a fully

open DHW valve.

There is no voltage.

Check the fuse/MCB

in your fuse box/

distribution panel.

Starting volume is not

achieved. The perlator in

the tap or shower head is

scaled up or dirty.

Clean and/or descale the

perlator or the shower

head.

The heating system is

faulty.

Contact your heating

contractor.

The air sensor detects air

in the water and briefly

switches the heater off.

The appliance restarts

automatically after one

minute.

Required temperature

>45 °C is not achieved.

Cold water inlet

temperature is > 45 °C.

Reduce the cold water

inlet temperature.

If you cannot remedy the fault, contact your heating contractor.

For better and faster help, provide him with the serial number

from the type plate (no. 000000-0000-000000):

DHB-E ...

26�02�02�0818

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiebel Eltron DHB-E 13 A Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info